User manual ONEFORALL URC 7557

[. . . ] English Table of Contents 2 3 3 PICTURE OF ONE FOR ALL 5 REMOTE INSTALLING THE BATTERIES THE KEYPAD SETTING UP THE ONE FOR ALL 5 (How to set up the ONE FOR ALL 5 to control your devices) SEARCH METHOD CODES · Televisions · Video Recorders · Satellite Receivers · Cable Converters · Video Accessory · Miscellaneous Audio · Amplifier · Amp. / Tuner · DVD 6 7 18 26 28 32 32 32 33 33 34 CODE BLINK OUT (To find out which code is currently programmed) QUICK CODE REFERENCE THE LEARNING FEATURE (How to copy functions from your original working remote onto the ONE FOR ALL 5) OPERATIONAL RESET EXTRA FEATURES · Mode re-assignment (Changing a device mode) · Volume Punch-Through · Macros (Sequence of commands) · Key Magic (How to program missing functions) · Colour and Brightness TROUBLE-SHOOTING 8 8 9 11 12 13 14 16 17 17 About Your ONE FOR ALL 5 Your ONE FOR ALL 5 can operate five devices: TV : Television VCR : Video Recorder SAT : Satellite Receiver or Cable Converter DVD : DVD Player AMP : Amplifier / Tuner Also, what makes the ONE FOR ALL 5 even more unique is the "Learning" feature, which allows you to customise any of the special functions of your original remote control onto the keypad of your new ONE FOR ALL 5. The following pages explain in simple steps how to customise the ONE FOR ALL 5 to your devices. You may need this guide again in the future, so please be sure to keep it. WWW. ONEFORALL. COM 1 1 2 3 4 5 7 6 9 8 10 11 12/13 14 2 WWW. ONEFORALL. COM Installing the Batteries Your ONE FOR ALL 5 requires 4 new "AAA/LR03" alkaline batteries. [. . . ] The TV key will blink twice. 4 For the first digit of your four-digit code, press 1 and count all the red blinks. If there are no blinks, the digit is "0". 5 For the second digit, press 2 and count all the red blinks. If there are no blinks, the digit is "0". 6 For the third digit, press 3 and count all the red blinks. If there are no blinks, the digit is "0". 7 For the fourth digit, press 4 and count all the red blinks. If there are no blinks, the digit is "0". Now you have your four-digit code. - To blink back the code for your other devices press the appropriat device key during step 1. Quick Code Reference Write down the codes for your devices in the boxes below and in the battery compartment for quick and easy reference. If there is a gap of more than 10 seconds between two steps, you will have to start again from step number 2. - If you learn a function on a key, the original ONE FOR ALL feature automatically becomes shifted. You can press MAGIC then the key to access it (this excludes the Channel and Volume keys). - The Learning feature is mode specific. Therefore you can place one learned feature per mode on the same key. - If a Shifted Learned function is placed on the Channel and Volume keys then Colour/Brightness will be sacrificed. - The ONE FOR ALL 5 can learn approximately 25 ­ 40 functions. - You can replace a learned function by placing another learned function on top. - Learning should not be done in direct sunlight or under incandescent lights. - Make sure you are using new batteries before following the instructions above. - Upon changing the batteries, your learned functions will be retained. · Shifted Learning You can also learn a function on a key of the ONE FOR ALL without sacrificing the original ONE FOR ALL function. A Shifted Learning function can also be put on any key EXCEPT for the following: Device keys, MAGIC key, Number keys. To install a Shifted Learning function, simply follow steps 1-8 on the previous page. During step 5, press MAGIC once before you press the key where you are placing the learned function. To access the shifted function, press MAGIC and then the key you have learned on. 10 WWW. ONEFORALL. COM The Learning Feature To delete a learned function: 1 Press and hold the MAGIC key until one of the device keys will blink twice. The red LED underneath the corresponding device key (depending on the device mode that was selected) will blink once then twice. [. . . ] All we need to know is: · The 5-digit set-up code your device is working with. · How the function was labelled on your original remote control. You can also visit our website (www. oneforall. com) to find an answer to your questions. Once you obtain(ed) your function code(s) from customer service, programming the code is easy: 1 2 Press the device key (TV, VCR, SAT, DVD and AMP). [. . . ]