User manual ONKYO A-9377

[. . . ] Integrated Amplifier Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 A-9377 Instruction Manual Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Thank you for purchasing the Onkyo A-9377 Integrated Amplifier. [. . . ] These buttons are explained on the next page. Buttons for Controlling the A-9377 The following buttons control the A-9377: D VOLUME [ ]/[ ] (16) Adjusts the volume of the A-9377. O INPUT [ ]/[ ] (16) Selects the input source: LINE, DOCK, PHONO, CD, TUNER, or TAPE. Q MUTING (16) Mutes the A-9377. 0 A 1 B C D 2 3 4 Q 5 6 7 8 9 H I O F 8 Introduction--Continued Buttons for Controlling Other Onkyo Components When other Onkyo audio components are connected to the A-9377 via , you can control them with the A-9377's remote controller. The operation of each button depends on the selected input source. For example, when the DOCK input source is selected, the [RANDOM] button will operate an RI Dock/iPod's Shuffle function. But when the TAPE input source is selected, it will operate a cassette deck's Dolby NR function. The following table lists the function of the remote controller's buttons for each input source. Where no function is listed, the button does nothing. Refer to each component's instruction manual for complete operating instructions. Input source Remote controller button CD [1]. . . [9] DOCK (RI Dock) CD (CD player) [1]. . . [9] [>10] [10/0] [BAND] [FM MODE] PRESET [+]/[­] ] [DIMMER] Pause [ Play [ Pause [ ] Rew/FF [ ] ] ]/[ ] ] Pause [ Play [ Stop [ Rew/FF [ ] ] ]/[ ] [DOLBY NR] [REV MODE] ] Reverse Play [ Play [ Stop [ ]*1 ]*1 ]*1 TUNING [ ]/[ ] TUNER (Tuner) TAPE (Cassette deck) 1 [>10] [10/0] [BAND] [FM MODE] PRESET [+]/[­] TUNING [ ]/[ ] ] ] ]/[ [DIMMER] Pause [ 2 3 5 6 7 8 Play [ Stop [ Rew/FF [ [RANDOM] [REPEAT] PLAYLIST [ ]/[ ]/[ ] ] [SHUFFLE] [REPEAT] PLAYLIST [ ALBUM [ ]/[ ]/[ ] ] [RANDOM] [REPEAT] 9 ALBUM [ MENU/SELECT [ ]/[ ] MENU/SELECT [ ]/[ ] [PLAY MODE] [SEARCH]*2 [MEMORY] [ENTER] [CLR] [BACKLIGHT] ] Prev/Next [ ]/[ ] [BACKLIGHT] [DISPLAY] [ Prev/Next ]/[ ] Rew/FF [ ]/[ ] 0 A B C D F H I [PLAY MODE] [GROUP/SEARCH] [MEMORY] [ENTER] [CLR] [DISPLAY] Prev/Next [ ]/[ [SCROLL] 1. On a double cassette deck, only deck B can be controlled. For use with MP3 CDs. Note: · With some components, some buttons may not work as expected. Refer to the component's instruction manual for complete operating instructions. 9 Introduction--Continued Installing the Batteries Aiming the Remote Controller When using the remote controller, point it toward the A-9377's remote control sensor, as shown below. 1 To open the battery compartment, press the small hollow and slide open the cover. Remote control sensor 2 Insert the two supplied batteries (AA/R6) in accordance with the polarity diagram inside the battery compartment. About 5 m (16 feet) 3 Slide the cover shut. Notes: · If the remote controller doesn't work reliably, try replacing the batteries. · Do not mix new and old batteries or different types of batteries. · If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion. · Expired batteries should be removed as soon as possible to prevent damage from leakage or corrosion. Notes: · The remote controller may not work reliably if the A-9377 is subjected to bright light, such as direct sunlight or inverter-type fluorescent lights. · If another remote controller of the same type is used in the same room, or the A-9377 is installed close to equipment that uses infrared rays, the remote controller may not work reliably. · Do not put anything on top of the remote controller, such as a book or magazine, because a button may be pressed continuously, thereby draining the batteries. · The remote controller may not work reliably if the A-9377 is installed in a rack behind colored glass doors. · The remote controller will not work if there's an obstacle between it and the A-9377's remote control sensor. 10 Connections Connecting Your Speakers You can connect one or two sets of speakers (A/B) to the A-9377 and select which set outputs sound, or use both sets simultaneously. Connecting the Speaker Cables 1 Speaker Connection Precautions · Always connect speakers in pairs. · If you want to output sound from speaker sets A and B simultaneously, you must use speakers with an impedance of 8 to 16 ohms. If you connect speakers with a lower impedance, and use the A-9377 at high volume levels for a long period, the built-in protection circuit may be activated. · If your speakers have an impedance of 4 to 8 ohms, connect them to either the SPEAKERS A or SPEAKERS B terminals, or do not output sound from both speaker sets simultaneously. [. . . ] Do not mix different types of batteries or old and new batteries (page 10). · Make sure that the remote controller is not too far away from the A-9377 and that there's no obstruction between the remote controller and the A-9377's remote control sensor (page 10). · Make sure that the A-9377 is not subjected to direct sunshine or inverter-type florescent lights. · If the A-9377 is installed in a rack or cabinet with colored glass doors, the remote controller may not work reliably when the doors are closed (page 10). Cannot control other components? · Make sure that all audio plugs are pushed in all the way (page 12). [. . . ]