User manual ONKYO A-9711

[. . . ] Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new Integrated Amplifier. Please retain this manual for future reference. Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When set to ON, the A-9711/A-9155 can be set to On or Standby. I (A-9711) PURE DIRECT button and indicator (16) This button turns the PURE DIRECT function on and off. The indicator lights up when the PURE DIRECT function is on. (A-9155) DIRECT button and indicator (16) This button turns the DIRECT function on and off. (MD recorder, TV, RI Dock, etc. ) K DOCK IN (A-9711 only) This analog audio input is for connecting a component's analog audio output (RI Dock, etc. ). B SPEAKERS A These terminal posts are for connecting speaker set A. L C SPEAKERS B These terminal posts are for connecting speaker set B. D AC OUTLETS These AC outlets can be used to supply power to another audio components. The type of outlets depend on the country in which you purchased the A-9711/A-9155. REMOTE CONTROL jacks The A-9711 has two jacks and the A-9155 has one. These (Remote Interactive) jacks can be connected to the jacks on your other Onkyo audio components. The A-9711/A-9155's remote controller can then be used to control all of your components. To use , you must make an analog audio connection between the A-9711/A-9155 and each component. E Power Cord After finished all the required connections, plug the power cord into a wall socket. See pages 10­14 for connection information. F PHONO (MM) input This analog audio input is for connecting a turntable with a moving-magnet cartridge. 7 Remote Controller Remote Controller (Buttons to control the A-9711/A-9155) 1 2 9 1 10 11 12 13 2 This section describes the function of the buttons to control the A-9711/A-9155. A STANDBY button (14) This button is used to set the A-9711/A-9155 to Standby. B ON button (14) This button is used to turn on the A-9711/A-9155. C VOLUME [ ]/[ ] buttons (15) These buttons adjust the volume of the A-9711/A-9155. 4 14 D INPUT [ ]/[ ] buttons (15) These buttons are used to select from the following input sources: LINE, HDD, PHONO, CD, TUNER, TAPE or MD. 3 E MUTING button (15) This button is used to mute the A-9711/A-9155. 3 5 4 5 6 7 8 15 16 Remote Controller (Buttons to control Onkyo products other than A-9711/A-9155) When other Onkyo audio components are connected to the A-9711/A-9155 via , you can control them by using the corresponding buttons for each component listed in the following table. Example: For 6 - Random button · When the A-9711 has a MD player connected to the LINE/MD terminal, or a CD player to the CD terminal, the button functions as "RANDOM" control. · When the A-9711 has a RI dock connected to the DOCK terminal, or the A-9155 has a RI dock connected to the LINE/DOCK terminal, the button functions as "SHUFFLE" control. · The button functions as "DOLBY NR" control, when a cassette deck is connected to the TAPE terminal. 8 Remote Controller--Continued DOCK (A-9711) LINE/DOCK (A-9155) Connecting Terminal Component and (Input Name) Button on Remote Controller 1-9 1 10/0 >10 BAND 2 FM MODE PRESET +/­ TUNING 3 4 5 6 7 / DIMMER LINE/MD (A-9711) CD TUNER TAPE MD Recorder (MD) RI Dock (DOCK) CD Player (CD) Tuner (TUNER) Cassette Tape Deck (TAPE) 1-9 10/0 >10 1-9 10//0 >10 BAND FM MODE PRESET +/­ TUNING DIMMER * * * / / RANDOM REPEAT PLAYLIST / / / RANDOM REPEAT / SHUFFLE REPEAT PLAYLIST ALBUM / / / RANDOM REPEAT DOLBY NR REV MODE 8 ALBUM MENU/SELECT/ / 9 10 11 12 13 14 15 16 PLAY MODE GROUP/SEARCH MEMORY ENTER CLR DISPLAY / SCROLL PLAY MODE GROUP MEMORY ENTER CLR DISPLAY / SCROLL MENU/SELECT/ / PLAY MODE SEARCH (MP3 CD) MEMORY ENTER CLR BACKLIGHT / BACKLIGHT DISPLAY / / · Note also that some of the connected products may not be controlled with these buttons. Use an analog audio cable to connect the A-9711/A-9155's PHONO L/R jacks to the audio output jacks on the turntable, as shown. If your amplifier has shorting pin plugs, remove the shorting pin plugs before connecting your turntable. Connecting a CD Player Use an analog audio cable to connect the A-9711/A-9155's CD L/R jacks to the analog audio output jacks on the CD player, as shown. ANALOG OUT AUDIO OUT Ground wire Notes: · If the turntable has a ground wire, connect it to A-9711/A-9155's GND terminal. With some turntables, connecting the ground wire may cause hum, in which case it should be disconnected. · If the turntable has a moving-coil (MC) type cartridge, you'll need a commercially available MC phono preamp. In this case, connect the turntable to the phono preamp's input, and connect the phono preamp's output to the A-9711/A-9155's PHONO L/R jacks. 11 Connecting the A-9711/A-9155--Continued Connecting a Tuner Use an analog audio cable to connect the A-9711/A-9155's TUNER L/R jacks to the analog audio output jacks on the tuner, as shown. Connecting a Remote Interactive Dock (RI Dock) Use an analog audio cable to connect the A-9711's DOCK Jack or A-9155's LINE/DOCK IN jack to the RI Dock's analog audio output jacks, and use an cable to connect the A-9711/A-9155's jack to the RI Dock's jack, as shown. OUT * Connecting a Cassette Deck Use an analog audio cable to connect the A-9711/A-9155's TAPE IN L/R jacks to the cassette deck's analog audio output jacks, and use another analog audio cable to connect the A-9711/A-9155's TAPE OUT L/R jacks to the cassette deck's analog audio input jacks, as shown. Remote Interactive Dock R ---- L AUDIO OUT * See page 13 to connect multiple audio components using jacks. Note: If you use the Onkyo Remote Interactive Dock (DSA1), flip the RI MODE switch to "HDD" which is located on the underside. Connecting a TV or Other Component with an Audio Output Use an analog audio cable to connect the A-9711's LINE/MD IN jack or A-9155's LINE/DOCK IN jack to the analog audio output jacks on the TV or other component, as shown. / REC (IN) PLAY (OUT) Connecting an MD Recorder Use an analog audio cable to connect the A-9711/A-9155's MD IN L/R jacks to the MD recorder's analog audio output jacks, and use another analog audio cable to connect the A-9711/A-9155's MD OUT L/R jacks to the MD recorder's analog audio input jacks, as shown. AUDIO OUT Note: If your TV has no audio output, you can connect the A-9711/A-9155 to an audio output on your VCR and use its tuner. REC (IN) PLAY (OUT) 12 Connecting the A-9711/A-9155--Continued Connecting Components · A-9711: The A-9711 has two jacks. If you want to connect two or more audio components to the A9355, it is advisable to connect any of two components directly to the A-9711 for better audio quality, in stead of linking all the components using the daisy chain method. · Use only dedicated cables for connections (no cables are supplied with the A-9711/A-9155). They're all the same, so you can use either of them. · jacks should be connected only to Onkyo components. Connecting them to another manufacturer's component may cause the A-9711/A-9155 to malfunction. · Some components may not support all functions. [. . . ] · Make sure that none of the cables are bent, twisted, or damaged. · To use a turntable with a moving-coil (MC) type cartridge, you need a commercially available MC phono preamp (page 11). · Verify if the SPEAKERS selector is configured correctly. If "OFF" is selected, no sound will be output from any of the speakers (page 14). Noise can be heard. · Using cable ties to bundle audio cables with power cords, speaker cables, and so on may degrade the audio performance, so don't bundle them together. [. . . ]