User manual ONKYO A-SV240

[. . . ] Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new Integrated Amplifier. Please retain this manual for future reference. Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · If the remote controller doesn't work reliably, try replacing the batteries. · Don't mix new and old batteries or different types of batteries. · If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion. · Expired batteries should be removed as soon as possible to prevent damage from leakage or corrosion. R SLEEP button S INPUT [ ]/[ ] buttons (17) These buttons are used to select from the following input sources: PHONO, TUNER, CD, LINE, MD, or TAPE/CDR. Using the Remote Controller Point the remote controller toward the remote control sensor. Remote control sensor T REPEAT button This button is used to set the repeat playback functions on an Onkyo Separate Collection CD, MD, or CDR component that's connected via . U DISPLAY button This button is used to change the information shown on the display. V SCROLL button This button is used to scroll text displayed on an Onkyo Separate Collection MD or CDR component that's connected via . ON 1 5 9 10/0 FM AM CD MD TAPE /CDR PRESE T STAN 2 6 7 >10 GROUP DBY 3 4 8 CLEA R VOLU ME MUTIN G VOLU ME TIMER SLEEP PRESE T W CLOCK CALL button This button is used to display the time on an Onkyo Separate Collection tuner that's connected via . MEMOR Y RANDO M P MODE CLOC CALL K RC-61 ENTE R REPEAT INPUT DISPLA Y SCROL L 3S About 5 m (16 feet) Installing the Batteries Remove the battery compartment cover, as shown. Insert the two supplied batteries (AA/R6) in accordance with the polarity markings in the battery compartment. Notes: · The remote controller may not work reliably if the A-SV240 is subjected to bright light, such as direct sunlight or inverter-type fluorescent lights. · If another remote controller of the same type is used in the same room, or the A-SV240 is installed close to equipment that uses infrared rays, the remote controller may not work reliably. · Don't put anything, such as a book, on the remote controller, because the buttons may be pressed inadvertently, thereby draining the batteries. · The remote controller may not work reliably if the A-SV240 is installed in a rack behind colored glass doors. · The remote controller will not work if there's an obstacle between it and the A-SV240's remote control sensor. Replace the battery compartment cover. 9 Connecting the A-SV240 About the System Functions If you connect another component from the Onkyo Separate Collection to the A-SV240 with the appropriate and audio cables, you can use the following system functions. cables are special cables solely for use with Onkyo products. (No cables are supplied with the A-SV240. ) Connecting components from the Onkyo Separate Collection. See page 13 for more information. Auto Power On When you turn on the power or start playback on a component that's connected to the A-SV240, the A-SV240 will turn on automatically. And when you set the A-SV240 to Standby, all connected components will go on Standby as well. · Be careful not to short the positive and negative wires. · Don't connect more than one wire to each speaker terminal. · Don't connect a speaker to more than one pair of speaker terminals. B SPEAKERS A R L R L 11 Connecting the A-SV240--Continued Connecting the Speaker Cables Connecting a Subwoofer 15 mm 1 Strip about 15 mm of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown. Unscrew the terminal. You can connect a subwoofer with a built-in power amplifier to the A-SV240's SUBWOOFER PREOUT jack. GND L L L SPEAKERS R PHONO (MM) R R TUNER CD B A LINE AC OUTLET R L R L AC 230-240V 50 Hz UNSWITCHED TOTAL 100W MAX. LINE INPUT 2 3 L SUBWOOFER PREOUT L L R MAIN IN OUT R MD IN OUT R IN TAPE/CDR REMOTE CONTROL INTEGRATED AMPLIFIER CAUTION: SPEAKER IMPEDANCE MODEL NO. /SPEAKER LINE INPUT Fully insert the bare wires. SUBWOOFER PRE OUT 4 Screw the terminal tight. The following illustration shows which speaker should be connected to each pair of terminals. Right speaker Speaker set A Left speaker Tip: The volume and quality of the bass output from your subwoofer will depend on its position, the shape of your listening room, and your listening position. In general, a good bass sound can be obtained by installing the subwoofer in a front corner, or at one-third of the way along the wall in front of your listening position. To find the best position for your subwoofer, while playing a movie or some music with good bass, experiment by placing your subwoofer at various positions within the room, and choose the one that provides the most satisfying results. ­ + ­ + L L L SPEAKERS R ONO (MM) R R TUNER CD B A LINE AC OUTLET R L R L AC 230-240V 50 Hz UNSWITCHED TOTAL 100W MAX. L L L R MAIN IN OUT R MD IN OUT R IN TAPE/CDR REMOTE CONTROL INTEGRATED AMPLIFIER CAUTION: SPEAKER IMPEDANCE MODEL NO. /SPEAKER A-SV240 ­ + ­ + Right speaker Speaker set B Left speaker 12 Connecting the A-SV240--Continued Hookup Diagrams for Onkyo Separate Collection The A-SV240 can be used with the Onkyo Separate Collection C-733 CD Player and T-433 Tuner as shown below. T-433 A-SV240 GND To wall outlet L L L SPEAKERS R PHONO (MM) R R TUNER CD B A LINE AC OUTLET R L R L AC 230-240V 50 Hz UNSWITCHED TOTAL 100W MAX. L SUBWOOFER PREOUT L L R MAIN IN OUT R MD IN OUT R IN TAPE/CDR REMOTE CONTROL INTEGRATED AMPLIFIER CAUTION: SPEAKER IMPEDANCE MODEL NO. /SPEAKER C-733 DIGITAL OUT OPTICAL ANALOG OUT REMOTE CONTROL L CONPACT DISC PLAYER MODEL NO. C- 733 R Connections · No cables are included with the A-SV240. Use the cables supplied with your other Onkyo Separate Collection components. [. . . ] · If the STANDBY indicator is flashing green, press the remote controller's [MUTING] button to unmute the A-SV240 (page 18). · Make sure that none of the cables are bent, twisted, or damaged. · Make sure that SPEAKERS A or B are selected. When only SPEAKERS A is selected (A indicator on), speakers connected to the SPEAKERS A terminals, and a connected subwoofer will output sound. [. . . ]