User manual ONKYO A-SV620

[. . . ] A built-in memory power back-up system preserves the contents of the memory during power failures and even when the unit is unplugged. The unit must be plugged in order to charge the back-up system. The memory preservation period after the unit has been unplugged varies depending on climate and placement of the unit. On the average, memory contents are protected over a period of a few weeks after the last time the unit has been unplugged. This period is shorter when the unit is exposed to a highly humid climate. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] · Direct Change Press the following button on the component you want to operate to switch the unit's input selector automatically to that component: ­ The play button on the CD player (or changer), MD recorder, or stereo cassette tape deck, or ­ The PRESET / buttons on the tuner. · Remote Control Operation All the system components can be operated using the supplied remote controller. The remote control buttons operate in the same way as the buttons on each component with the same indication. · Program Timer You can operate timer playback and recording using T-405TX. (Refer to the T-405TX instruction manual for more information. ) · Sleep Timer You can fall asleep to a music/radio program using the timer. (Refer to the T-405TX instruction manual for more information. ) · CD Dubbing Simple CD dubbing using a stereo cassette tape deck or MD recorder is possible with the pressing of a single button (CD dubbing function using an MD recorder is not avalable on the C-707CHX). (Refer to the K-505TX or MD-105TX Instruction Manual for more information). · CD/MD Synchro Recording When using a stereo cassette tape deck, MD recorder or CD recorder to record from the CD player or when using a stereo cassette tape deck to record from an MD recorder, you can record with simply starting on a CD player or MD recorder. (Refer to the K-505TX, MD-105TX or CDR-205TX instruction manual for more information. ) · Dubbing a specific track from CD You can specify a track on a CD and easily dub it to a connected MD recorder or CD recorder. (Refer to the MD-105TX or CDR-205TX instruction manual for more information. ) 6 Arranging the system components Combination example 1 Select the tuner T-405TX, CD player C-705TX (or CD changer C-707CHX), and stereo cassette tape deck K-505TX in addition to this unit. When you arrange these components, stack them as shown below. (If you try to connect an Onkyo tape deck, MD recorder, or CD recorder that has connectors in this way, a malfunction may occur. Do not use the cables for connections. ) You can connect a digital audio processor for a personal computer to the CDR/PC connector. Connections About the processor's connectors You can connect a sound processor (e. g. graphic equalizer, surround processor, etc. ) to the unit. Before connecting · Disconnect the jumper plugs using the PROCESSOR connectors. ­ Please retain them for future use. ­ Never connect the jumper plugs to the other connectors, as this may cause the unit to malfunction, so that the sound is not reproduced. ­ If you do not use the PROCESSOR connectors, reconnect the jumper plugs to them firmly. Note: When connecting jumper plugs, make sure you hold the plugs horizontally as shown in the figure and connect each plug to the IN and OUT jacks. Preparations PRO OUT SO CES IN Jumper plug Operation R Connect the sound processor to the unit. This unit OUT(REC) IN (PLAY) L CAUTION: SPEAKER IMPEDANCE 4 OHMS MIN. /SPEAKER INPUT L L SPEAKERS R R TUNER LINE/DVD OUT(REC) IN(PLAY) TAPE REMOTE CONTROL OUT(REC) IN (PLAY) R L AC OUTLET Sound processor Other Information R AC 230-240V CDR/PC CD MD OUT PROCESSOR IN SUBWOOFER PRE OUT 50Hz SWITCHED 100W MAX. OUTPUT OUT(REC) IN(PLAY) L R TUNER CD MD OUT PROCESSOR IN SUBWOOFER PRE OUT : Signal flow 13 Connecting to components other than the Separate Collection Series Connecting the cables connec- If your other components are made by ONKYO and those components are equipped with -connected components with the supplied remote controller. tors, you can control the Before connecting · The unit must be connected in the system hookups for control operations. There is no difference between these connectors. · Each component has two · The components may be connected in any order. [. . . ] · Jumper plug is not connected to the PROCESSOR connectors. · The volume level is turned down to the minimum. · The batteries in the remote controller are dead. · The remote controller is out of the control range. [. . . ]