User manual ONKYO ABX-100

[. . . ] Dock Music System Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . En-2 ABX-100 Instruction Manual Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . En-7 Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . En-8 Playing Your iPod/iPhone . . . . . . En-9 Setting the Clock. . . . . . . . . . . . . . . . . . . . . En-11 Thank you for purchasing an Onkyo Dock Music System. Please read this manual thoroughly before making any connections and plugging it in. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new Dock Music System. [. . . ] Please note that the use of this accessory with iPod or iPhone may affect wireless performance. En-4 Supplied Accessories Make sure you have the following accessories: Replacing the Battery Use only a battery of the same type (CR2025). 1 While sliding the stopper to the side, pull out the battery holder. Back side Remote controller (RC-806S) and battery (CR2025) AC adapter (DC output 15V 2A) (Adapter varies from country to country. ) 2 Insert a lithium button battery in the battery holder, and then replace the holder. Positive (+) side Note: • The AC adapter supplied with the ABX-100 is designed exclusively for use with the ABX-100. Likewise, do not use any other AC adapter with the ABX-100. Doing so may damage the ABX-100. Using the Remote Controller Remove the plastic film before using the remote controller. Notes: • If the remote controller doesn’t work reliably, try replacing the battery. • If you intend not to use the remote controller for a long time, remove the battery to prevent damage from leakage or corrosion. To remove the adapter, lift the back side up. If the adapter is difficult to remove, insert a thin object into the slot and lift the adapter up. Use the Universal Dock Adapter that’s appropriate for your model of iPod/iPhone. If a Universal Dock Adapter was included with your iPod, use that adapter. If none was included, purchase the appropriate adapter separately. Note: • Inserting your iPod/iPhone into the dock without the appropriate adapter may damage the dock connector. En-7 Basic Operation M DIMMER INPUT C/U MENU F/H TONE S. BASS ENTER INPUT F/H VOL H/F Downlight (below the speakers) M ON/STANDBY MENU ENTER VOLUME F/H MUTING Turning On the ABX-100 To turn on the ABX-100, press the [ ON/STANDBY] button on the ABX-100 or remote controller. Press the [ ON/STANDBY] button again to set the ABX-100 to Standby. If an iPod/iPhone is connected to the ABX-100, the iPod/ iPhone will be charged. Changing the Downlight Brightness (remote controller only) You can adjust the brightness of the downlight. Press the remote controller’s [DIMMER] button repeatedly to select normal, dim or off. ABX-100 Selecting the Input Source You can select iPod or LINE, which can be an external component. To select the input source, use the remote controller’s INPUT []/[] buttons. On the ABX-100, press the [INPUT] button repeatedly. Downlight Adjusting the Bass and Treble Adjusting the Volume Press the VOL Up [] button to increase the volume or the VOL Down [] button to decrease it. You can also use the remote controller’s VOLUME []/ [] buttons. 1 2 3 4 5 Press the [TONE] button to make the display indicate “Tone Control. ” Use the []/[] buttons to adjust the value. You can adjust the value in the range of –3 to +3. The value of the Treble setting will blink. Use the []/[] buttons to adjust the value. The original display will reappear. Muting the ABX-100 (remote controller only) To mute the ABX-100, press the remote controller’s [MUTING] button. “Muting” appears on the display for a few seconds. To unmute the ABX-100, press the [MUTING] button again. Tips: While the ABX-100 is muted: • Press the VOL []/[] buttons on the ABX-100 or pressing the VOLUME []/[] buttons on the remote controller will unmute the ABX-100. [. . . ] • Make sure the ABX-100 is turned on, the input source is set to iPod, and the volume is not set too low. • Make sure that your iPod/iPhone is compatible with the system (see page 4). External Components No sound is heard from your turntable. • Make sure the turntable has a built-in phono equalizer. If the turntable doesn’t have a phono equalizer builtin, you must provide one. Timers The timers don’t work. • Make sure the clock has been set correctly (see page 11). • Timed operation will fail if the ABX-100 is already on at the specified On time, so make sure it’s set to Standby (see page 11). [. . . ]