User manual ONKYO CHR-185X

[. . . ] 37 Listening to the Radio . . . . . . . . . . . . . . . . . . 39 Instruction Manual Enjoying the Listening Modes . . . . . 45 Thank you for purchasing an Onkyo 7. 1ch THX Certified Digital Surround Receiver and Speaker Package. Please read this manual thoroughly before making connections and plugging in the unit. [. . . ] For example, if you connect your DVD player to COMPONENT VIDEO IN 2, you must assign COMPONENT VIDEO IN 2 to the DVD input selector. To upconvert and output composite video and S-Video sources from the COMPONENT VIDEO OUT, select the VIDEO setting. Here are the default assignments. Input selector DVD VIDEO 1 VIDEO 2 VIDEO 3 Default assignment IN1 VIDEO VIDEO VIDEO SETUP Note: · This procedure can also be performed on the AV receiver by using the [SETUP], [ENTER], and arrow buttons. 1 RECEIVER Press the [RECEIVER] button, followed by the [SETUP] button. SETUP 36 Playing Your AV Components Basic AV Receiver Operation MULTI CH 1 TUNING PRESET 4 MASTER VOLUME ON/STANDBY REMOTE MODE RECEIVER DVD M D/CDR 1 TAPE 1 Subwoofer's rear panel INPUT SELECTOR 1 V1 2 V2 3 V3 CD HDD STANDBY/ON STANDBY 4 ENTER 5 MULTI CH 6 DVD TV 7 MULTI CH DVD VIDEO 1 VIDEO 2 VIDEO 3 TAPE TUNER CD RETURN SETUP 8 TUNER 9 CD VCR 12 CABLE TAPE 10 11 +10 VCR VIDEO 3 INPUT PHONES SPEAKERS A B TONE THX LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE VIDEO L AUDIO R 0 ENT DIMMER CLR SLEEP SAT D TUN --/--- CLEAR TV INPUT GUIDE TOP MENU VOL DISC ALBUM CH VOL 4 2 DISPLAY 2 PREVIOUS MENU SP A / B MUTING ENTER PLAYLIST/CAT PLAYLIST/CAT 1 AV receiver DVD VIDEO 1 VIDEO 2 VCR VIDEO 3 TAPE TUNER Remote controller RECEIVER Use the AV receiver's input selector buttons to select the input source. To select the input source with the remote controller, press the [RECEIVER] REMOTE MODE button, and then use the INPUT SELECTOR buttons. 1 V1 2 V2 3 V3 CD 6 DVD On the remote controller, the [V1], [V2], and [V3] buttons select the VIDEO 1, VIDEO 2, and VIDEO 3 input sources respectively. 7 TAPE 8 TUNER 9 CD 2 AV receiver SPEAKERS A B Remote controller To turn the speakers on or off, use the AV receiver's SPEAKERS [A] and [B] buttons, or use the remote controller's [SP A/B] button. Pressing the remote controller's [SP A/B] button cycles through the following settings: Speaker Set A Speaker Set A&B Speaker Set B Off. Note that while speaker set B is on, speaker set A is reduced to 5. 1-channel Indicators playback. See page 8 for more information about speaker sets A and B. 3 4 AV receiver MASTER VOLUME Start playback on the source component. To watch a DVD or other video source, on your TV, select the video input that's connected to the AV receiver's MONITOR OUT jack. Remote controller VOL To adjust the volume, use the MASTER VOLUME control, or the remote controller's [VOL] button. The volume can be set to ­ dB, ­83. . . 0. . . +16 dB. Since the AV receiver is designed for home theater enjoyment, it has a wide volume range for precise adjustment. To set the level of the subwoofer, use the OUTPUT LEVEL control. Note: · You can also use the remote controller's Up and Down [ ]/[ ] buttons to tune the radio. 1 TUNING MODE Press the [TUNING MODE] button so that the AUTO indicator appears on the display. 2 TUNING PRESET Press the TUNING Up or Down [ ]/[ ] button. Searching stops when a station is found. 39 Listening to the Radio--Continued Tuning into Stations by Frequency You can tune into AM and FM stations directly by entering the appropriate frequency. ON/STANDBY REMOTE MODE 2 MEMORY Press the [MEMORY] button. The MEMORY indicator appears and the preset number flashes. RECEIVER TAPE DVD M D/CDR RECEIVER INPUT SELECTOR Number buttons D TUN 1 V1 2 V2 3 V3 CD HDD 4 7 TAPE 5 MULTI CH 6 DVD TV 3 CH +/­ TUNING PRESET 8 TUNER 9 CD VCR 12 CABLE 10 11 +10 D TUN 0 ENT DIMMER CLR SLEEP SAT --/--- While the MEMORY indicator is displayed (about 8 seconds), use the PRESET [ ]/[ ] buttons to select a preset from 1 through 40. ENTER TV INPUT GUIDE TOP MENU VOL DISC ALBUM CH VOL PREVIOUS MENU SP A / B MUTING ENTER PLAYLIST/CAT PLAYLIST/CAT 4 MEMORY RETURN SETUP 1 RECEIVER Press the [RECEIVER] button, followed by the [D TUN] button. Press the [MEMORY] button again to store the station. The station is stored and the preset number stops flashing. Repeat this procedure for all of your favorite AM/FM radio stations. Selecting Presets D TUN (Actual display depends on country. ) The [RECEIVER] button flashes. Within 8 seconds, use the number buttons to enter the frequency of the radio station. For example, to tune to 87. 5 (FM), press 8, 7, 5. Note: While the [RECEIVER] button is flashing, the input source cannot be changed by using the remote controller. 1 TUNING PRESET 2 ENTER To select a preset, use the PRESET [ ]/[ ] buttons, or the remote controller's CH [+/­] button. DISC ALBUM CH Deleting Presets 1 Presetting Radio Stations PRESET MASTER VOLUME TUNING PRESET Select the preset that you want to delete. While holding down the [MEMORY] button, press the [TUNING MODE] button. The preset is deleted and its number disappears from the display. 2 MEMORY TUNING MODE CLEAR STANDBY/ON STANDBY ENTER MULTI CH DVD VIDEO 1 VIDEO 2 VIDEO 3 TAPE TUNER CD RETURN SETUP VCR VIDEO 3 INPUT PHONES SPEAKERS A B TONE THX LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE VIDEO L AUDIO R CLEAR MEMORY TUNING MODE You can store a combination of up to 40 of your favorite AM and FM radio stations as presets. 1 40 Tune into the station that you want to store as a preset. Listening to the Radio--Continued Using RDS (European Models Only) RDS only works with European models and only in areas where RDS broadcasts are available. When tuned into an RDS station, the RDS indicator appears. RDS indicator RDS Program Types (PTY) Type None News reports Current affairs Display NONE NEWS AFFAIRS Description No program type. [. . . ] · With some AV components, certain buttons may not work as expected, and some may not work at all. · To control an Onkyo component that's connected via , point the remote controller at the AV receiver. Be sure to enter the appropriate remote control code first (see page 58). · To control an Onkyo component that's not connected via , or another manufacturer's component, point the remote controller at the component. [. . . ]