User manual ONKYO CR-325

[. . . ] Contents CD Receiver Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . 2 CR-525 CR-325 Instruction Manual Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Basic Operations . . . . . . . . . . . . . . . . . . . . 25 Playing a Disc. . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] You can adjust the volume and mute the sound, as explained earlier. The speakers output no sound while the headphones are connected. PHONES jack Turn the [VOLUME] control clockwise to increase the volume or counterclockwise to decrease it. You can also use remote controller's VOLUME [ ]/[ ] buttons. 25 Basic Operations--Continued / TONE ENTER S. BASS MUTING DIRECT Adjusting the Bass and Treble Using the Direct Function To turn the Direct function on or off, press CD receiver the [DIRECT] button on the CD receiver. When the Direct function is off, the tone controls can be used to adjust the sound. When the Direct function is on, the tone controls are bypassed, so you can enjoy a pure sound, and the DIRECT indicator lights up. DIRECT indicator 1 Remote controller Press the [TONE] button to select "Bass". 2 Use the Previous and Next [ ]/[ ] buttons to adjust the bass. The default setting is "±0". You can adjust the bass and treble from ­3 to +3. Press [ENTER], and then use the Previous and Next [ ]/[ ] buttons to adjust the treble. Notes: · If you press no buttons for 8 seconds, the previous display will appear automatically. · If you press the [TONE] button while the Direct function is on, the Direct function will be turned off. On the remote controller, press the [TONE] button for 3 seconds to turn on the Direct function. Muting the Sound To mute the output of the CD receiver, press the remote controller's [MUTING] button. The MUTING indicator flashes on the display. The volume control indicator flashes, too. MUTING indicator Remote controller Using the Super Bass Function Remote controller To turn on the Super Bass function, press the [S. BASS] button. To turn off the Super Bass function, press the [S. BASS] button again. Note: If you press the [S. BASS] button while the Direct function is on, the Direct function will be turned off. To unmute the CD receiver, press the [MUTING] button again. Tips: While the CD receiver is muted: · Turning the [VOLUME] control on the CD receiver or pressing the VOLUME [ ]/[ ] buttons on the remote controller will unmute the CD receiver. · If you turn the CD receiver off, the next time you turn it on, the CD receiver will be unmuted. 26 Basic Operations--Continued Changing the Input Display You can choose what name is displayed when an input source is selected so that it matches the type of component that you've connected to the MD/TAPE IN. When you connect an Onkyo -capable component, it's important that you select the input source name that matches the type of component for to work properly. 4 INPUT / MENU/NO / ENTER Press [ENTER] to confirm your selection. "Complete" appears on the display. Input Source Name Abbreviations Sometimes the input source name may be displayed as a 2-letter abbreviation, as per the following table. Full name Abbreviation DT MD TP VD 1 Use the INPUT [ ]/[ to select "TAPE". ] buttons DAT MD TAPE VIDEO 2 Press and hold the [MENU/NO] button until "Name Select?" appears on the display, and then press [ENTER]. HOLD 3 Use the Previous or Next [ ]/[ ] button to select the new input source name. The input source names are selected in the following orders: TAPE MD DAT* * When you select an input source name, you cannot select it as the recording component at the set timer recording. VIDEO* 27 Playing CDs Display Disc tray 1 Press the Open/Close [ ] button to open the disc tray. Tip: Pressing the Open/Close [ ] button while the CD receiver is on Standby will turn on the CD receiver and open the disc tray. Place the CD on the tray with the label-side facing up. Place 8 cm CDs in the center of the tray. To start playback, press the Play/Pause [ / ] button. The disc tray closes and playback starts. [. . . ] No sound is heard from a connected component. · Make sure the correct input source is selected (see page 25). · Make sure the analog audio cable is connected correctly (see pages 21 to 23). · Make sure that all audio connecting plugs are pushed in all the way (see page 20). [. . . ]