User manual ONKYO CR-515DAB

[. . . ] Contents CD Receiver Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . 2 CR-515DAB CR-315DAB Instruction Manual Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Basic Operation . . . . . . . . . . . . . . . . . . . . . . 27 Playing a Disc. . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Tips: While the CD receiver is muted: · Turning the [VOLUME] control on the CD receiver or pressing the VOLUME [ ]/[ ] buttons on the remote controller will unmute the CD receiver. · If you turn the CD receiver off, the next time you turn it on, the CD receiver will be unmuted. 28 Basic Operation--Continued Changing the Input Display You can choose what name is displayed when an input source is selected so that it matches the type of component that you've connected to the MD/TAPE IN, DOCK/CDR IN, or DIGITAL IN. When you connect an Onkyo -capable component, it's important that you select the input source name that matches the type of component for to work properly. Depending on the input source selected in step 1, the input source names are selected in the following orders: INPUT / MENU/NO/ CLEAR / YES/MODE ENTER DIGITAL GAME/dig DOCK PC CD-R/dig PC/dig TAPE MD DAT CD-R VIDEO 1 Use the INPUT [ ]/[ ] buttons to select the input source whose name you want to change. CR-515DAB: TAPE, DOCK, DIGITAL CR-315DAB: TAPE Press and hold the [MENU/NO/CLEAR] button until "Name Select?" flashes on the display, and then press [ENTER]. 4 Press [ENTER] to confirm your selection. "Complete" appears on the display. 2 On the CR-515DAB, you can also use the front panel controls. 1 Use the [INPUT] button to select the input source whose name you want to change. 2 Push the multi control to select "Name Select?, " and then push it again. 3 Turn the multi control to select the new input source name. 4 Push the multi control to confirm your selection. 3 Use the Previous or Next [ ]/[ ] button to select the new input source name. Input Source Name Abbreviations Sometimes the input source name may be displayed as a 2-letter abbreviation, as per the following table. Full name CDR DAT DIGITAL GAME DOCK LINE LINE1 LINE2 MD PC TAPE VIDEO Abbreviation CR DT DG GM DC LI L1 L2 MD PC TP VD 29 Playing CDs CR-515DAB Display CR-315DAB Display Disc tray / Disc tray / 1 Press the Eject [ ] button to open the disc tray. Tip: Pressing the Eject [ ] button while the CD receiver is on Standby will turn on the CD receiver and open the disc tray. Place the CD on the tray with the label-side facing up. Place 8 cm CDs in the center of the tray. To start playback, press the Play/Pause [ / ] button. The disc tray closes and playback starts. To stop playback: Press the Stop [ ] button. Playback stops automatically when the last track has been played. To pause playback: Press the Play/Pause [ / ] button. To resume playback, press the Play/Pause [ / ] button again. To remove the CD: Press the Eject [ ] button to open the disc tray. "DISC TOTAL" lights up while the disc information is being displayed. Selecting Tracks (CR-515DAB) To return to the beginning of the track currently playing, turn the multi control a little to the left. Turn the multi control further to select earlier tracks. · While playback is stopped, turn the multi control to the left to select the previous track. Turn the multi control to the right to select subsequent tracks. [. . . ] The CD receiver's remote control sensor is being subjected to bright light (inverter-type fluorescent light or sunlight). The CD receiver is located behind the glass doors of a audio rack or cabinet. External Components Interactive control with other Onkyo -capable components is not working. · Make sure the cables and analog audio cables are connected correctly (see pages 19 to 25). Connecting only an cable won't work. [. . . ]