User manual ONKYO CR-555DAB

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] · To use you must make an analog RCA/phono connection between the CR-555DAB and the other component even if they are connected digitally. · If a component has two connectors, you can connect either one to the CR-555DAB. The other connector is for connecting additional -compatible components. · Connect the CR-555DAB's connector only to Onkyo components. Connecting to other manufacturer's components may cause them to malfunction. · Some Onkyo -compatible components may not support the special functions described above. 15 Powering Up and Setting the Clock VOLUME If you are using any model other than the European, please skip to "Setting the Clock Manually" on page 18. MIN STANDBY / ON PHONES INPUT MENU DIRECT BASS TREBLE PRESET MAX ACCUCLOCK Function (for European models only) PUSH TO ENTER STANDBY/ ON CLOCK CALL CLOCK CALL TIMER STANDBY/ON Standby indicator 1 4 2 5 8 --/--- 3 TIMER 6 9 7 10/0 CLEAR Powering Up the CR-555DAB Before connecting the power cord, complete all connections (see pages 11 to 15). ENTER DISPLAY MODE ENTER DISPLAY SLEEP REPEAT MUTING INPUT 1 Connect the power cord to a suitable wall outlet. The CR-555DAB enters Standby mode, and the Standby indicator comes on. CD DIRECT 2 To turn on the CR-555DAB, press the [STANDBY/ON] button. The CR-555DAB comes on, the display lights up, and the Standby indicator goes off. To turn off the CR-555DAB, press the [STANDBY/ON] button again. The CR-555DAB enters Standby mode and the Standby indicator comes on. The very first time you turn on the CR-555DAB, the ACCUCLOCK function automatically sets the clock by using the CT (Clock Time) information present in RDS radio broadcasts. While the clock is being set, "WAIT" appears on the display, as shown. It may take a while to set the clock. When the clock has been set, "ADJUSTED" appears on the display for a while. Use the [CLOCK CALL] button to check if the clock has been set correctly. If you select a track while playback is stopped, press the [/ ] control to start playback. Press the [ / ] control to jump to the next track during playback. On the remote controller: Press the [ ] button to select the next track, or the [ ] button to select the previous track. If you press the [ ] button during playback or while playback is paused, the beginning of the current track is selected. If you select a track while playback is stopped, press the Play [ ] button to start playback. Note: With CDs and MP3 discs that contain many tracks, playback may take a while to start. Playing CDs Selecting Tracks by Number You can use the number buttons to select specific tracks. Label side 1 Press the [ ] button to open the disc tray, put the CD on the tray with the label-side facing up, and press the [ ] button again to close the tray. 1 Use the number buttons to enter a track number. Playback starts automatically. For MP3 disc, select the serial number assigned to the track. To enter a track number smaller than or equal to 10, press each number button. For example, to enter track number 10, press [10/0]. Use the [--/---] button to enter track numbers above 10. To enter a track number from 11 through 99, press [--/---] once. [. . . ] Condensation has formed inside the CR505. It takes a long time to locate certain tracks. For European models: Does not operate during the ACCUCLOCK function with a message "WAIT" displayed. For European models: The clock is wrong? [. . . ]