User manual ONKYO CR-N1

[. . . ] English CD RECEIVER CR-N1 Instruction Manual Before using 2 Controls & connectors 12 Getting connected 18 Basic operation 30 Playing CDs 35 Listening to the radio 41 Thank you for purchasing the ONKYO CR-N1 CD Receiver. Please read this manual thoroughly before making any connection or turning on the power. Follow these instructions to obtain optimum performance and maximum listening enjoyment from your new CR-N1. Please retain this manual for future reference. Using the timer 47 Using USB 51 Appendix 58 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] Dust and lint can be removed from the speaker grilles by using a soft brush, or a vacuum cleaner with a brush attachment. D-N1 Specifications Type Impedance Maximum input power Output sound pressure level Frequency response Crossover frequency Cabinet capacity 2-way bass reflex 4 30 watts 83 dB/W/m 63 Hz­35 kHz 3 kHz 2. 6 liter Woofer: 9 cm cone x1 Tweeter: 2. 5 cm dome x1 165 x 271 x 160 mm (6-1/2" x 10-11/16" x 6-5/16") 1. 7 kg (3. 7 lbs) Magnetic shielding Symmetrical type 1 meter speaker cable x2 Note: Do not attempt to carry the speaker by holding only its grille. There is a risk that the speaker will be dropped if the grille separates from the cabinet. Speakers Dimensions (W x H x D) Weight Others Supplied accessories Specifications and features are subject to change without notice. 22 Getting connected Connecting an AM antenna The bundled AM loop antenna is designed for indoor use only. Using the bundled AM loop antenna 1. Assemble the AM antenna, as shown. Make sure that the wires are attached securely and that the terminals are gripping the bare wires, not the insulation. Once the CR-N1 is ready for use, you'll need to tune into an AM radio station and adjust the position of the AM antenna in order to achieve the best possible reception. Keep it as far away as possible from the CR-N1, speaker cables, power cord, and your computer. Using an outdoor AM antenna Insert into the hole. If good reception cannot be achieved using the bundled AM loop antenna, an outdoor AM antenna can be used as well, as shown. Outdoor antenna The AM antenna needs to be connected to the AM terminals located on the rear of the CR-N1, as shown. 2. To connect an antenna wire, push the terminal lever, insert the bare wires, and then release the lever, as shown. 1. Insert Outdoor AM antennas work best outside, but good results can sometimes be obtained indoors by mounting horizontally above a window. Note that the AM loop antenna should be left connected. Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards. See item 14 of "Important safeguards" at the front of this manual. 3. Release 23 Getting connected Connecting an FM antenna The bundled indoor FM antenna is designed for indoor use only. Using an outdoor FM antenna If good reception cannot be achieved using the bundled indoor FM antenna, an outdoor FM antenna can be used instead, as shown. Using the bundled FM antenna 1. and Canadian models Strip the insulation from the end of the cable and insert the bare wires fully into the FM terminal, as shown. Other models Once the CR-N1 is ready for use, you'll need to tune into an FM radio station and adjust the position of the FM antenna in order to achieve the best possible reception. Use thumbtacks (drawing pins) or something similar to fix the antenna into position. Outdoor FM antennas work best outside, but good results can sometimes be obtained indoors by mounting in an attic or loft. Outdoor antenna should be located away from possible noise sources, such as neon signs, busy roads, etc. For safety reasons, outdoor antenna should be situated well away from power lines. Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards. See item 14 of "Important safeguards" at the front of this manual. Using a TV antenna It's best not to use the same antenna for both FM and TV reception, as this can cause interference problems. If circumstances demand using the same antenna, use a TV/ FM antenna splitter, as shown. TV/FM antenna splitter To CR-N1 To TV or VCR 24 Getting connected Using the 75/300 ohm FM antenna adapter (The 75/300 ohm antenna adapter is not included with the U. S. , Canadian, and European models. ) The 75/300 ohm antenna adapter can be used to connect an FM antenna with 300 ohm flat twin-core cable, or to connect an FM antenna with a 75 ohm coaxial cable with no connector attached. Connecting 75 ohm coaxial cable 1. Using a small screwdriver or your fingernails, push the tabs outwards and remove the adapter's cover, as shown. 2. Move the wire inside the adapter from position A to position B, as shown. Position A Connecting 300 ohm flat twin-core cable 1. Undo the two adapter screws, wrap the bare wires around the screws, and then retighten the screws, as shown. Position B Outdoor antenna Indoor antenna 300 ohm flat twin-core cable Wire 3. Prepare the end of the 75 ohm coaxial cable and place it in the adapter, as shown. 636 mm mm mm 1 15 mm 2 2. [. . . ] RDS doesn't work. Try changing the position and direction of the outdoor FM antenna. Locate the FM antenna as far away as possible from any fluorescent lights. Place the CR-N1 somewhere free from vibration. Load the disc with the labeled side facing forwards. [. . . ]