User manual ONKYO DV-SP300

[. . . ] Contents Before Using Your DVD Player 2 DVD Player Getting Started 6 DV-SP300 Facilities and Connections 10 Instruction Manual Basic Operation 17 Advanced Operation 20 Thank you for purchasing the Onkyo DVD Player. Please read this manual thoroughly before making connections and turning on the power. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new DVD Player. Please retain this manual for future reference. Function Setup 30 Others 37 E WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] DV-SP300 PB R S VIDEO Y DO NOT connect the power cord until all connections are complete. To audio input L R An amplifier or receiver with stereo inputs Making stereo audio connections Using an audio cable (sold separately), make audio connections from the ANALOG OUTPUT L and R jacks to the corresponding jacks on the stereo component. Be sure to set Digital Audio Out setting to "PCM" using the setup menu explained in "Customizing the Settings" starting on page 30. See page 35 for direct information. Notes · Be sure to match the colors of the plugs on the cable with the corresponding jacks on the DVD Player and the stereo component: red for R (right) audio and white for L (left) audio. · Do not make connections to the PHONO or TUNER jacks on the stereo component. Audio cable (not supplied) Audio (L) Audio (R) Analog signal Coaxial plug Digital signal Optical plug Digital signal Signal flow 16 Turning on Connecting the POWER The DV-SP300 is shipped with the main power (POWER) switch in the on position ( ON). When the power cord is plugged in for the first time, the DV-SP300 will automatically enter the standby mode and the STANDBY indicator will light (same condition after step 2 below). POWER STANDBY/ON Notes · Make sure that all appropriate connections have been completed as described on pages 14 to 16. · Turning on the DVD Player may cause a momentary power surge, which might interfere with other electrical equipment such as computers. To prevent interference, use a wall outlet on a different circuit. STANDBY indicator 1 2 Plug the power cord into the power outlet on the wall. Press POWER to switch on the main power. The DVD Player enters standby mode. The STANDBY indicator lights up. Notes · The buttons on the remote controller do not operate if the POWER switch is set to OFF. · To switch off the main power, press POWER again. STANDBY/ON 3 Press STANDBY/ON on the DVD Player or remote controller. The DVD Player turns on and the STANDBY indicator turns off. It takes several seconds to read the disc in the disc tray. Notes · You can turn on the DVD Player by pressing 0 or £/8. · To put the DVD Player in the standby mode, press STANDBY/ON on the DVD Player, or remote controller. Be sure to set the volume to minimum before putting the DVD Player in the standby mode for the next use to avoid sudden loud sound reproduction. · While the STANDBY indicator lights up, the DVD Player can receive signals from the remote controller. However, if you press POWER on the DVD Player to switch off the main power, the remote controller cannot be used to turn on the DVD Player. · Setting the STANDBY button to standby does not shut off the power completely. 17 DVD VCD CD Basic Playback Before playing · DVD-Video, Video CD, CD can be played with the DVD Player (see "Playable Discs" on page 6). · When playing DVD-Video or Video CD with video features, turn on the TV and set the TV to the DVD Player's input. · If an audio system is connected to the DVD Player, turn on the audio system and set it to the DVD Player's input. Warning If the DVD Player is connected to the TV or amplifier through the analog audio jacks, do not play DTS-encoded discs. Excessive noise may be output from the analog stereo jacks, which may damage the connected equipment. To reproduce DTS surround sounds, digital connection to an amplifier with a DTS decoder is needed. About the DVD , VCD and CD marks in the pages related to disc operation DVD means the function or title is related to DVD-Video operation. VCD means the function or title is related to Video CD operation. CD means the function or title is related to audio CD operation. Starting Playback STOP 7 PLAY/PAUSE £/8 Disc tray 0 OPEN/CLOSE SKIP 4/¢ SEARCH 1/¡ 1 I To stop playback Press 0 OPEN/CLOSE. The disc tray opens. If the DVD Player is in standby mode when the 0 OPEN/CLOSE button is pressed, the DVD Player turns on and the disc tray opens. In this case, it takes several seconds until the disc tray opens. Press STOP 7. When you press PLAY/PAUSE £/8 to restart playback, playback starts from the location where you stopped playback because the location index is stored in memory. Note The location where playback resumes may vary depending on the disc or the scene where you stopped. Playback from the beginning 2 3 Place a disc on the disc tray. Put the disc in the tray with the label side facing up. [. . . ] · Sometimes a small amount of picture distortion may appear. Pages 17 17 17 ­ 18 4 6 18 18 7 32 14 25 7 ­ DVD Player Playback doesn't follow the course of the disc's programs. The picture from the DVD Player doesn't appear on the TV screen. No sound or inaccurate sound is reproduced. · The DVD Player is in repeat playback mode, memory playback mode, or random playback mode, etc. [. . . ]