User manual ONKYO DV-SP301

[. . . ] 00_DV-SP301. book Page 1 Friday, April 18, 2003 4:18 PM Contents Before Using Your DVD Player 2 DVD Player Getting Started 6 DV-SP301 Instruction Manual Facilities and Connections 10 Basic Operations 17 Advanced Operations 22 Thank you for purchasing the Onkyo DVD Player. Please read this manual thoroughly before making connections and turning on the power. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new DVD Player. Function Setup 30 Please retain this manual for future reference. Others 37 En 00_DV-SP301. book Page 2 Friday, April 18, 2003 4:18 PM WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] If the amplifier has a Dolby Pro Logic decoder, you can reproduce the Dolby Pro Logic surround sound. Note DO NOT connect to the AC-3RF input (e. g. of a Dolby Digital receiver) which is reserved only for video disc players. Be sure to set the "Digital Audio Out" setting after connection using the Setup explained on page 33. Digital cable (Not supplied) To digital input (optical) DIGITAL OPTICAL To digital input (coaxial) DIGITAL COAXIAL Coaxial cable (Supplied) To audio inputs L Signal flow Audio (L) Audio (R) Audio (L) R An amplifier or receiver with a Dolby Digital or DTS decoder or digital input jacks Audio (R) Audio cable (Supplied) To z jack REMOTE CONTROL z cable (Supplied) VIDEO OUTPUT COMPONENT AUDIO OUTPUT PR DIGITAL OPTICAL COAXIAL ANALOG REMOTE CONTROL L DVD PLAYER VIDEO PB MODEL NO. DV-SP301 R S VIDEO Y Connect the power cord after all connections are complete. 16 00_DV-SP301. book Page 17 Friday, April 18, 2003 4:18 PM Turning on Connecting the POWER The DV-SP301 is shipped with the main power (POWER) switch in the on position (_ON). When the power cord is plugged in for the first time, the DV-SP301 will automatically enter the standby mode and the STANDBY indicator will light (same condition after step 2 below). Notes · Make sure that all appropriate connections have been completed as described on page 13 to 16. · Turning on the DVD Player may cause a momentary power surge, which might interfere with other electrical equipment such as computers. To prevent interference, use a wall outlet on a different circuit. POWER STANDBY/ON STANDBY indicator 1 2 Plug the power cord into the power outlet on the wall. Press POWER to switch on the main power. The DVD Player enters standby mode. The STANDBY indicator lights up. STANDBY/ON Notes · The buttons on the remote controller do not operate if the POWER switch is set to OFF. · To switch off the main power, press POWER again. · The system remains in standby mode for 5 seconds after the power is turned on. 3 Press STANDBY/ON on the DVD Player or remote controller. The DVD Player turns on and the STANDBY indicator turns off. It takes several seconds to read the disc in the disc tray. Notes · You can turn on the DVD Player by pressing OPEN/ CLOSE 0 or PLAY/PAUSE £/8. · To put the DVD Player in the standby mode, press STANDBY/ON on the DVD Player, or remote controller. · While the STANDBY indicator lights up, the DVD Player can receive signals from the remote controller. However, if you press POWER on the DVD Player to switch off the main power, the remote controller cannot be used to turn on the DVD Player. · Setting the STANDBY/ON button to standby does not shut off the power completely. 17 00_DV-SP301. book Page 18 Friday, April 18, 2003 4:18 PM Basic Playback Before playing · Turn on the TV and set the TV to the DVD Player's input. · Turn on the audio system and set it to the DVD Player's input, if an audio system is connected to the DVD Player. · DVD-Video, Video CD, CD, MP3, WMA, JPEG can be played with the DVD Player (see "Notes on Discs" on page 6 and 7). About the marks in the pages related to disc operation DVD means the function or title is related to DVD-Video operation. VCD means the function or title is related to Video CD operation. CD means the function or title is related to audio CD operation. MP3 means the function or title is related to MP3/WMA sound operation. Both MP3 and WMA are referred to as MP3 in the following pages. [. . . ] · The DVD Player is not properly connected. · Check the connections to the DVD Player. · A wrong sound signal conversion method (Digital Audio Out) is selected. · Check the current sound signal conversion method, and select the right setting for "Digital Audio Out". [. . . ]