User manual ONKYO DX-7711

[. . . ] Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain the optimum performance and listening enjoyment from your new DX-7711. Please retain this manual for future reference. Main Features · · · · · · CD/CD-R/CD-RW Disc Compatibility Auto Finalizing Function 32kHz/44. 1kHz/48kHz Sampling-Rate Converter 1 Optical/1 Coaxial Digital Inputs Signal Synchro Recording Name input function allowing you to specify a disc name, track titles, and an artist name. · Adjustable Recording Volume (Digital/Analog) · High-Resolution D/A & A/D Converter · 1 Optical/1 Coaxial Digital Outputs · z Cable Included WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] The operation will be resumed in response to any recordable signals that may follow. I Synchronous recording on the DX-7711 (The recording on the DX-7711 and the playback on the source device start simultaneously. ) · Synchronous recording from the CD player to the DX-7711 · Synchronous recording from the MD recorder to the DX-7711 (Analog recording only) Note: If you want to record digitally from the CD player, you must have the optical or coaxial cable from the CD player connected to the DIGITAL INPUT terminal on the DX-7711. Do not turn off the DX-7711 while making recordings, finalizing discs, or erasing recordings, or while "PMA Writing" is displayed An inserted disc can be corrupt and no longer usable if the power is accidentally turned off or in case of power failure. 18 Recording modes About the level sync function The level sync function detects the space between tracks (songs, etc. ) in the recording source and automatically assigns track numbers to them during recording. Name function I Entering a disc name or artist name (see page 28) You can enter one disc name and one artist name per disc. I When the level sync function is turned on The track numbers are updated automatically. Press the o REC button to set track numbers manually . I Entering track names (see page 31) You can enter up to 99 track names per disc. I When the level sync function is turned off The track numbers are not updated automatically. Press the o REC button to set track numbers manually . I Erasing the disc name, artist name, and track names (see page 32) You can erase all the name information retained in the DX-7711. I For analog recording The level sync function automatically turns On. If there are gaps of no sound 2 seconds or longer between tracks in the recording source, the track numbers will be automatically updated. Finalization The finalization process writes the TOC data (tracks, etc. ) for the disc in a special area on the disc called the PMA. After finalization, CD-Rs can be played in CD players. Even after finalization, CD-RWs can only be played on CD players that are compatible with CD-RWs. For CD-Rs that have been finalized, you cannot add more recordings. I For digital recording The level sync recording automatically turns on. If the digital signal includes the track number information, the track numbers will be automatically assigned. For satellite broadcasts and other digital signals that do not include track number information, the track numbers will be automatically updated when 2 seconds or more of silence is detected. Erasing recording (CD-RW discs only) The data recorded on CD-RW discs can be erased and the disc can be used again as many times as desired (see page 34). · Erasing data on unfinalized CD-RWs Last track erase: Erases only the last track. Multi-track erase: Erases all tracks from the selected track to the final track. · DATs and DCCs cannot be recorded if no start ID is present before audio contents. · Synchronous recording uses a sub-code signal that is contained in the digital output from most player components, and therefore there may be some CD players, MD recorders, or the like where digital synchronous recording is impossible. 1 Repeatedly press the INPUT button and select the desired input signal. Select "Digital In 1, " "Digital In 2, " or "Analog In" for the input source. INPUT Proceed to step 3 if you do not wish to adjust the recording level. 2 Start playback of the recording source. 3 Press the o REC button. "Rec Setup" appears in the display followed by the time display. DX-7711 RC-448C REC Preparation · Turn on the DX-7711 (see page 16). · Place a recordable CD-R or CD-RW in the DXR700 (see page 17). · Verify that the input dial and recording selection button of the amplifier are set to the position of the recording source. REC Proceed to step 6 if you do not wish to adjust the recording level. 22 Synchronous recording by input signal detection (Signal synchronous recording) 4 Adjust the recording level. Refer to page 21, step 4 "Adjust the recording level. " Auto finalization To use auto finalization, press the FINALIZE button repeatedly during recording until "Auto On" appears. (The FINALIZE indicator appears flashing. ) Finalization starts automatically when the DX-7711 is set in the state of "Signal Wait" for 1 minute after interruption of the input signal. · If "Name Disc" appears when you press the FINALIZE button You cannot use auto finalization. This is because the disc has track names but it has no disc name. Enter a disc name after recording completes (see page 28). Press the FINALIZE button to finalize the disc (see page 33). 5 Stop the playback of the recording source. 6 Press the o REC button. The DX-7711 enters the input standby state, "Signal Rec" appears in the display, and then "Signal Wait" appears flashing alternately with the time display. DX-7711 REC RC-448C REC To cancel auto finalization Press the FINALIZE button repeatedly until "Auto Off" appears. (The FINALIZE indicator disappears. ) Note: If "Check Level" flashes and recording does not start, then the recording source was likely already playing and not allowing recording to start. [. . . ] Connect the components following the procedure given in "Connecting the DX-7711" on page 15. Switch to a properly connected input source (see pages 20, 22, 24). Adjust the recording level to a proper level (see page 21). Connect the components following the procedure given in "Connecting the DX-7711" on page 15. [. . . ]