User manual ONKYO DX-C110

[. . . ] 12 Index Search . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Notes about the Remote Control Transmitter . . . . . . . . . . . . . . . . . 13 Notes about Handling Compact Discs . . . . . . . . . . . . . . . . . . . . . . . 13 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . [. . . ] Connect the "LINE OUT" terminals to the "CD" (or "AUX") terminals of the amplifier. If the amplifier does not have such terminals, use the "TAPE PB" terminals. For additional details concerning these connections, refer to the operation instructions for the amplifier being used. q q Be sure that the left (L) and right (R) LINE OUT terminals are connected to the corresponding (left and right) terminals of the amplifier or other component. If the placement of this unit causes noise to other equipment, such as a tuner, separate them from each other. This unit To AC outlet Connection cord (included) Amplifier 4 IDENTIFICATION OF COMPONENTS FRONT PANEL POWER switch DISC -select button DISC SKIP button OPEN/CLOSE button STOP button PLAYXCHANGE button Disc tray PLAY/PAUSE button TIME display modeselect button Display panel SKIP button SEARCH button PROG button OUTPUT LEVEL control Disc play MODE-select button REPEAT button PHONES jack RANDOM button Remote control sensor REMOTE CONTROL TRANSMITTER The control functions on the main unit and on the remotecontrol transmitter are virtually identical, with the exceptions described below. DIMMERbutton CLEAR button Numeric buttons INDEX button * The PLAY/PAUSE button on the main unit has both the functions of the PLAY button and the PAUSE button on the remote control transmitter * Remote control transmitter has two DISC SKIP buttons. Pressing each button will search discs in the direction shown by the arrow. 5 LOADING THE DISC/DISC PLAY 6 1 5 1 5 Select the disc play mode (DISC MODE: SINGLE or ALL) while watching the display. 6 2, 4 6, 3 2 Label side upward Shows the selected disc mode. "SINGLE" mode: The unit will play a designated disc only. "ALL" mode: The unit will play all discs in the tray in sequence. Disc tray 6 3 * If necessary, select a desired disc by using a DISC-select button or the DISC SKIP button. 4 q Notes After closing the disc tray by pressing the OPEN/CLOSE button in the stop mode or after selecting any disc by using the DISC SKIP button, the display shows the total number of tracks and the total recorded time of the disc to be played for a few seconds. q Additionally, you can close the disc tray by pressing the PLAY/PAUSE button, a DISC-select button, a numeric button (on the remote control transmitter) or the RANDOM button, or by pressing the front edge of the disc tray gently. If the tray is closed in these ways, play will begin automatically, however, the display will not show the total number of tracks and the total recorded time of the first disc to be played. PLAYXCHANGE During play, you can open the disc tray by pressing the PLAYXCHANGE button without interrupting disc play. However, in this case, pressing the DISC SKIP button has no effect. 6 To stop play temporarily To stop play completely or * To resume play, press the PLAY/PAUSE button again (or press the PLAY or PAUSE button on the remote control transmitter). To play a desired track on the disc DIRECT PLAY Select a desired track by using the numeric buttons on the remote control transmitter. SKIP PLAY q To play from the beginning of the track following the one now playing q To play from the beginning of the track now playing The selected track number is displayed. q To play from the beginning of the track before the one now playing Example: To select track 25 Press twice, then immediately press once. (twice) * These operations can also be performed when the unit is in the pause or stop mode. * If a track number higher than the highest track number on the disc is selected, the last track on the disc will be played. Display information at disc play Encloses the tray number of the disc standing by to be played or the disc now playing. (Refer to "Selecting time displays" on the next page. ) Displays the numbers that correspond to the numbers of the tracks (as high as number 20) on the disc. After each track is played, its corresponding number disappears so the number of remaining tracks (and their numbers) can be seen at a glance. 7 To advance or reverse play rapidly (MANUAL SEARCH) To advance rapidly q q (press and hold) The sound can be heard (although slightly garbled) during manual search in either direction. Press a numeric button on the remote control transmitter to select a track to replace the one displayed. The previously programmed track will be cleared from the memory and the new one will be programmed. After the correction has been completed, press the PROG button or PLAY/PAUSE button once again. 11 REPEAT PLAY You can play any desired track or disc (set of discs) repeatedly by pressing the REPEAT button. The repeat play mode will change whenever you press the REPEAT button. SINGLE REPEAT (S REP) (OFF) A single track is repeatedly played. * This is also available in the programmed-play mode and the random-sequence play mode. (If the repeat play mode is switched off, the programmed-play mode or the randomsequence play mode will be resumed. ) or FULL REPEAT (F REP) In the "SINGLE" disc play mode: A designated disc is played repeatedly. In the "ALL" disc play mode: All discs in the disc tray are repeatedly played. * In the programmed-play mode, all programmed tracks are repeatedly played. * In the random-sequence play mode, all randomly sequenced tracks are repeatedly played in the same order. INDEX SEARCH If the disc includes index numbers, play can be started from any desired index number. 1 To cancel the index search function Select a track which has index numbers. Notes q Not all discs have index numbers. The index system is a method for sub-dividing tracks into smaller divisions (such as, for example, the movements within classical symphonies) for easier location of those parts. The liner notes with the disc usually tell if such index numbers are included. [. . . ] Wait 20 to 30 minutes after switching the unit ON before trying to play a disc. Check the disc carefully; replace it if necessary. If the problem persists, the cables may be defective. Set the amplifier controls to the correct input selection. [. . . ]