User manual ONKYO DX-C210

[. . . ] 5 Identification of Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Random-Sequence Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Program Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Every time the play of a disc is finished, the corresponding tray number is changed from flashing to lighting. DISC SCAN q q There might be cases that you will hear no sound during disc scan. An example of this would be if the disc being played has a long blank space between tracks. Selecting time displays You can select any of the four time displays by pressing the TIME display mode-select button. Elapsed time of the track now playing 5DISC Total remaining time on the disc 5DISC TOTAL REMAIN 2 3 4 5 6 7 8 9 10 1 1 12 2 3 4 5 6 7 8 9 10 1 1 12 TIME Remaining time of the track now playing 5DISC REMAIN 2 3 4 5 6 7 8 9 10 1 1 12 Total disc play time 5DISC TOTAL 2 3 4 5 6 7 8 9 10 1 1 12 Note The remaining time will not be displayed if the track number is 21 or higher. 11 Changing brightness of the display CDC-765 You can change the brightness of the display (or turn off the illumination) by pressing the DIMMER button. During play Normal illumination During stopped or paused Normal illumination DIMMER Dim Dim "OFF" * When the display illumination is off, the AUTO DISPLAY OFF indicator on the front panel lights up. Dim (The AUTO DISPLAY OFF indicator lights up. In this state, if a disc is played, the display illumination will be turned off. ) AUTO DISPLAY OFF DX-C210, CDC-565 If desired, you can change brightness of the display in three degrees by pressing the DIMMER button. DIMMER Normal illumination Slightly dim Dim CDC-765 and DX-C210 only Adjusting the level of signals output into an amplifier, etc. You can adjust the level of sound signals output from the LINE OUT terminals on the rear panel into an amplifier, etc. as you prefer by using the OUTPUT LEVEL button. CDC-765 and DX-C210 only When you listen with headphones Connect the headphones to the PHONES jack and adjust the volume by using the OUTPUT LEVEL button. * Note that the use of the OUTPUT LEVEL button will also vary the level of the signal output to an amplifier, etc. PHONES ­ OUTPUT LEVEL + OUTPUT LEVEL or ­ + (On the front panel) * When the DIGITAL AUDIO OUT (OPTICAL) terminal is used for the connection, set the level of output signals to max. * The level of output signals can be checked on the display. 12 English RANDOM-SEQUENCE PLAY You can play the tracks in a random sequence (up to 99 tracks). The unit will automatically mix up tracks from all discs or a designated disc on the disc tray. CDC-765, DX-C210 SYNCHRO DIMMER TIME OPEN/ CLOSE TAPE 1 2 3 CLEAR PROG CDC-565 2 4 3 DISC SKIP SYNCHRO DIMMER TIME OPEN/ CLOSE CLEAR 1 2 3 PROG 2 4 INDEX INDEX 3 DISC SKIP 4 5 6 +I0 4 5 6 +I0 7 8 9 0 7 8 9 0 DISC SCAN MODE REPEAT RANDOM DISC SCAN MODE REPEAT RANDOM DISC SKIP SEARCH DISC SKIP SEARCH ­ OUTPUT LEVEL + PAUSE SKIP SKIP STOP PLAY STOP PAUSE PLAY 1 Load one or more discs. 3 Select a desired disc play mode (1DISC or 5DISC). MODE * If you select "1DISC" mode, next select a desired disc by using the DISC SKIP button on the remote control transmitter or a DISC-select button on the front panel. 2 Close the disc tray. OPEN/ CLOSE 4 RANDOM "RNDM" lights up on the display. To cancel random-sequence play Press the STOP button or RANDOM button once again, or open the disc tray by pressing the OPEN/CLOSE button. "RNDM" disappears from the display. Notes q This feature will not function during programming, or during program play. q If the SKIP button is pressed during random-sequence play, the next randomly programmed track will be played. If the SKIP button is pressed, play will return to the beginning of the track now being played. This indication appears while the unit is mixing up tracks. Total remaining time on the disc will not be displayed during random-sequence play. q q 13 PROGRAM PLAY You can enjoy listening to your favorite tracks selected from one or more discs in any desired order by programming tracks. CDC-765, DX-C210 CDC-565 SYNCHRO DIMMER TIME OPEN/ CLOSE SYNCHRO DIMMER TIME OPEN/ CLOSE TAPE 1 2 3 CLEAR PROG INDEX 3 5 7 2, 4 1 CLEAR 1 2 3 PROG INDEX 3 5 2, 4 1 4 5 6 +I0 4 5 6 +I0 7 8 9 0 7 8 9 0 DISC SCAN MODE REPEAT RANDOM DISC SCAN MODE REPEAT RANDOM DISC SKIP SEARCH DISC SKIP SEARCH ­ OUTPUT LEVEL + PAUSE SKIP SKIP STOP PLAY STOP PAUSE PLAY 7 1 Stop the unit. STOP 4 If necessary, select a desired disc. DISC 3 DISC SKIP 2 4 or (On the front panel) 2 If you will select tracks from a disc (or discs) other than the disc on the Disc 1 tray, make this unit display the total recorded time of each disc to be used by pressing the DISC SKIP button in turn. Press a numeric button to select a track to replace the one displayed. The previously programmed track will be cleared from the memory and the new one will be programmed. After the correction has been completed, press the PROG button or PLAY button once again. 15 PROGRAM FILING for CDC-765 only You can make this unit store (file) program data of your own choosing. With this function, you can play a disc with your favorite program at any time without making it again. However, note that you can not file program data which consists of tracks selected from more than one disc. SYNCHRO DIMMER TIME OPEN/ CLOSE OPEN/CLOSE PROG TAPE 1 2 3 CLEAR PROG INDEX Numeric buttons DISC SKIP 4 5 6 +I0 7 8 9 0 DISC SCAN MODE REPEAT RANDOM DISC SKIP SEARCH ­ OUTPUT LEVEL + PAUSE SKIP STOP PLAY STOP PLAY FILE/SAVE PROG DISC / (PLAY/PAUSE) NATURAL SOUND COMPACT DISC PLAYER CDC-765 / OPEN/CLOSE PLAYXCHANGE OPEN/CLOSE (STOP) AUTO DISPLAY OFF FILE/ SAVE PROG 1 2 DISC 3 4 5 SKIP/SEARCH POWER PHONES +10 1 2 3 4 5 6 7 8 9 0 OUTPUT LEVEL PEAK ­ + POWER Numeric buttons 0 To file program data 1 2 Follow step 1 ­ 4 on page 14. 3 FILE/ SAVE Select track numbers in a desired order. 1 2 3 SAVE (On the front panel) +I0 4 5 6 7 8 9 0 * If programming of tracks has already completed, make sure that "TRACK" is flashing continuously on the display. If it is not flashing, press the PROG button. (If a program play is being performed, press the STOP button, and then press the PROG button. ) Notes q Program data filed in this way can be retained for about two weeks with the power switched off. q One program data can be filed for one disc. If different program data is filed for a disc, the previous program data will be deleted from the file, and only the new program data will be retained in the file. q Program data for a total of as many as about 100 discs can be filed. 16 English To play with program data To delete program data from file 1 Load a disc which has its program data in this unit's memory's file. 1 2 If the unit is playing a disc, press the STOP button. * If a program play is on standby, press the STOP button to cancel that program sequence. [. . . ] Wait 20 to 30 minutes after switching the unit ON before trying to play a disc. Check the disc carefully; replace it if necessary. If the problem persists, the cables may be defective. Set the amplifier controls to the correct input selection. [. . . ]