User manual ONKYO DX-C220

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. [. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/ TV technician for help. In addition to ordinary CDs, CD-Rs or CD-RWs can be read by this unit. However, NEVER use a CD-R or CD-RW that contains no data or data in the wrong format, such as MP3 or other computer files. When you insert a CD-R/CD-RW, it may take longer to start playing. CAUTION Modifications or adjustments to this product, which are not expressly approved by the manufacturer, may void the user's right or authority to operate this product. 1 ENGLISH PRECAUTIONS · Do NOT install the unit in a location where it may be subjected to: -- Direct sunlight or other sources of excessive heat -- Fluid, rain or moisture -- Excessive dirt or dust -- Excessive vibration · This unit is designed to be operated on a 12-volt DC negative-ground electrical system only. · Choose the mounting location carefully so that the unit will not interfere with normal driving functions. · Before making connections, disconnect the ( terminal of the car battery to avoid short circuiting. · Clean the discs before inserting them into the disc magazine. Always clean a disc from the center outward with a cleaning cloth. Notes on CDs · A defective or soiled disc stored in the disc magazine can cause the sound to drop out during play. · Be sure to set both levers to the same position. · Be sure to set the levers exactly at the position (notch). If the lever is deviate from the position, the sound may drop out. · Care must be taken when you mount the unit at the angle of lower than level. The disc magazine may drop if you eject the magazine. · Do NOT turn over the unit or slide the lever when the unit is activated. Doing so may damage the mechanism or the discs in the unit. · The mounting angle setting levers on each side of the unit are factory-set to the HORIZONTAL position. · When you complete the setting, attach the supplied adhesive labels e over the slots. ENGLISH 4 INSTALLATIONS Horizontal installation 1 Construction For details on abc. . . , see page 3. The effective angle of the unit. The position of the lever. ;; ; ;; ; ; ; Note If the mounting surface needs to be strengthened, secure the plate brackets c to the bottom surface of the car trunk, etc. with the tapping screws (not supplied). 2 Deciding the position 4 Making holes in the carpet 3 Removing temporarily 5 Completion 5 ENGLISH Vertical installation 1 Construction For details on abc. . . , see page 3. The effective angle of the unit. [. . . ] · When you complete the setting, attach the supplied adhesive labels e over the slots. ENGLISH 4 INSTALLATIONS Horizontal installation 1 Construction For details on abc. . . , see page 3. The effective angle of the unit. The position of the lever. ;; ; ;; ; ; ; Note If the mounting surface needs to be strengthened, secure the plate brackets c to the bottom surface of the car trunk, etc. with the tapping screws (not supplied). 2 Deciding the position 4 Making holes in the carpet 3 Removing temporarily 5 Completion 5 ENGLISH Vertical installation 1 Construction For details on abc. . . , see page 3. The effective angle of the unit. The position of the lever. 30° 15° V Notes · If the mounting surface needs to be strengthened, secure the plate brackets c to the bottom surface of the car trunk, etc. · If installation space is narrow, bend the plate bracket c back and forth along the perforated line to break off the end. ;; ;; ; ; ; ; 2 Deciding the position 4 Making holes in the carpet Cut the plate bracket c if it is too long. 3 Removing temporarily 5 Completion ENGLISH 6 INSTALLATIONS Suspended installation When installing the unit in the trunk below the package tray, observe the following. [. . . ]