User manual ONKYO DX-C390

[. . . ] Compact Disc Changer Getting Started 2 DX-C390 Instruction Manual Connection 12 Basic Operation 14 Thank you for purchasing an Onkyo Compact Disc Changer. Please read this manual thoroughly before making connections and turning on the power. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new Compact Disc Changer. Please retain this manual for future reference. Advanced Operation 20 Others 25 En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] · To use you must make an analog RCA/phono connection between your DX-C390 and Onkyo AV receiver even if they are connected digitally. · The DX-C390 has two connectors. You can connect either one to your Onkyo AV receiver. The other connector is for connecting additional -compatible components. · Connect the DX-C390's connector to only Onkyo AV components. Connecting to other manufacturer's AV components may cause them to malfunction. · Some Onkyo -compatible AV components may not support the special functions described here. To use you must make an analog audio connection (RCA/phono) between the DX-C390 and your other Onkyo equipment even if they are connected digitally. Disconnect the power cord before making any connections! cable Coaxial cable (not supplied) RCA/phono audio connecting cable L CD R Coaxial IN Hi-fi amp, AV receiver 13 Turning On the DX-C390 North American Model STANDBY/ON Basic Playback PLAY/PAUSE DIMMER Other Models STANDBY/ON DISC SKIP POWER Turning On the DX-C390 Before connecting the power cord and turning on the DX-C390, connect all your AV components first (see page 12). Don't forget to turn on your amp, and select the audio input to which the DX-C390 is connected. Loading Discs 1 To open the disc tray, press the [ ] button. Put a disc, label-side up, into each disc bay. 1 2 Connect the power cord to a suitable wall outlet. Set the [POWER] switch to the ON position (does not apply to the North American model). The DX-C390 enters Standby mode, and the STANDBY indicator comes on. Notes: · The DX-C390 is shipped with the [POWER] switch in the ON position. · The remote controller cannot be used to turn on the DX-C390 while the [POWER] switch is in the OFF position. Press the [STANDBY/ON] button or the remote contoller's [ON] button. The DX-C390 comes on, the display lights up, the disc tray light comes on, and the STANDBY indicator goes off. When the DX-C390 is turned on, it checks the carousel for discs and selects the first disc that it finds. To set the DX-C390 to Standby, press the [STANDBY/ON] button or the remote controller's [STANDBY] button. Current disc 2 To access the other disc bays, use the [DISC SKIP] button or the remote controller's DISC [+] and [­] buttons. To close the disc tray, press the [ ] button again. AIN 3 3 1 4 2 5 3 6 A circle appears around the number of the current disc. Notes: · The DX-C390 supports 8 cm and 12 cm discs. To avoid damaging your discs or DX-C390, be sure to put discs in the centers of the disc bays. · Only load discs that are supported by the DX-C390 (see page 6). · To avoid personal injury, keep your hands away from the disc tray as it closes. [. . . ] Make sure that the DX-C390 is not subjected to direct sunshine or inverter-type fluorescent lights. Open the doors, or use a cabinet without colored glass. Load the disc with the label-side facing up (page 14). Remove your discs and leave the DX-C390 turned on for several hours until the condensation has evaporated. [. . . ]