User manual ONKYO DX-C600

[. . . ] Make sure speakers are connected correctly before plugging the AC power cord into an AC outlet. CAUTION : . TO PREVENT ELECTRICAL SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. . Be sure the AC power cord is disconnected and all functions are off before making connections. FM ANTENNA . Do not connect to an outside antenna. [. . . ] NOTE: Do not connect FM wire antenna to external antenna. Rotate the set to get the best receiving position. TO RECEIVE THE FM BROADCAST IN STEREO Set the MODE switch to FM STEREO. When the FM stereo broadcast is received, FM STEREO indicator lights up. IF THE FM STEREO BROADCAST SIGNAL IS WEAK Set the MODE switch to MONO position to reduce background noises but the sound becomes monaural. AFTER LISTENING switch to STANDBY. Set the FUNCTION : 9/0N "UO!1!SOd 1:>eJJO:> SleU!WJe1 Je>leeds e41 01 SeJ!M e411:>euu00 U!~NI. l:)3NNO:) S~3)fV3dS . I. 1. Set to CD. 2. Open the CD door. FUNCTION TII~CK TAPE O STANDBY =:-1 1": TUNER CD ~ -. . 3. Place a disc onto the disc(s) label side up. holder, with the 4. Press the DISC SKIP button to revolve the tray clockwise. Place other disc(s) on the disc holder(s). DISCSKIP ~ 5. Close the CD door by holding down on its center until secure. The total number of tracks will show in the CD display in a few seconds and the indicator of the current disc will light up TRACK 6. Press the DISC SKIP button to select the desired disc. Press either one of the ~/~ F. SKIP buttons to select the desired track. F. SKIP B. SKIP/ TRACK DISC SKIP ~ DI~9 DIsc2 '. /c. =. ;;>- / I' DI~O B. SKIP ~ 7. Set the FUNCTION to TAPE. 2. Insert tapes into the cassette compartments FUNCTION TAPE ~ STANDBY =:l. r: TUNER CD ~ . . . - ~ . (r~ -+, . - Played next 3. Press the PLAY button on DECK B. 4. Press DECK the A. PAUSE and PLAY buttons on ~ PLAY ~ PlAY REW FFWD STOP/EJECT PAUSE . As soon as the tape in deck B reaches its end and stop, the pause mode for deck A is released and playback starts automatically. Use only normal (type I) tapes for recording and playback. 1. Set the FUNCTION to TAPE. 2. Insert the recorded blank tape into Deck B and the tape into Deck A. FUNCTION TAPE <!> STANDBY =:-1 r: TUNER CD Tape to be ~ recorded . ~ Tape . to be played ~ (~~~ -+. - 3. Set the MODE selector according to the desired dubbing speed: NORMAL or HIGH. NORM DUBBING HIGH 2 BEAT CUT 1 FMMONO FMSTEREO ~~ 4. Press the PAUSE button ~ PAUSE ((Q) 4 ~ 5. Press the RECORD button engages the PLAY button. ~ ~ PLAY which also 6. Press the PLAY button. ~ PLAY TO STOP ~; ~ ~, , DUBBING STOP/EJECT buttons of Deck A and NOTE: Do not change in progress. the dubbing speed when dubbing is Press the DeckB. , ~ . . , " c. ~ Use only normal (type I) tapes for recording. Set the FUNCTION to TUNER and tune to your desired station. FUNCTION TAPE <!>STANDBY~L:CD TUNER 2. Insert a tape into the cassette compartment. ~ ~ ~ -+. . I (Q)rn@o -This button which also side you want to record 3. Press engages the RECORD the PLAY button. ~ PLAY ~ . If a whistle is heard (beat) it may be reduced by switching the "Beat Cut" to the other position. ~ ~nTC RECORDING FROM THE BUILT -IN CD PLAYER 1. [. . . ] 6. REPEAT Button ~ SKIP Button ~ SKIP Button DISC SKIP Button ~I PLAY/PAUSE Button . STOP Button USING THE CORRECTLY REMOTE CONTROL . Point the Remote Control at the REMOTE SENSOR located on the unit. . When there is a strong ambient light source, the performance of the infrared REMOTE SENSOR may be degraded. . The recommended effective distance for remote operation is about 4 meters (13 feet). NOTE: When open the CD door, the remote control cannot be worked at once TO INSTALL BATTERIES 1. Insert two RO3 (MA or SUM-4) size batteries BATTERY REPLACEMENT When batteries become weak, the operating distance of the Remote Control is greatly reduced and you will need to replace the batteries. [. . . ]