User manual ONKYO DX-R700

[. . . ] Contents Before using Audio CD Recorder 2 DX-R700 Instruction Manual Connections 14 Operations 16 Thank you for purchasing the Onkyo Audio CD Recorder. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new Audio CD Recorder. Please retain this manual for future reference. Other Information 42 Before using Thank you for purchasing . . . Thank you for purchasing the Onkyo DX-R700 CD Recorder. [. . . ] · Erasing data on unfinalized CD-RWs Last track erase: Erases only the last track. Multi-track erase: Erases all tracks from the selected track to the final track. · Erasing data on finalized CD-RWs All track erase: Erases all tracks. TOC erase: Returns a finalized disc to the unfinalized conditions. · Erasing discs Erases all data recorded on the CD-RW. 19 Digital recording/Analog recording q MULTI JOG w INPUT STANDBY/ ON OPEN / CLOSE RANDOM MEMORY REPEAT ABC DUAL DIGITAL INPUT STANDBY/ON PAUSE STOP PLAY DEF 3 NAME 1 2 GHI 4 MEMORY STANDBY CLEAR DISPLAY MULTI JOG INPUT JKL 5 MNO 6 SCROLL PQRS PHONES REPEAT FINALIZE EDIT/ NO PUSH TO ENTER TUV 8 W XYZ 9 CLEAR PHONES LEVEL POWER YES 7 REC DISPLAY MIN MAX ENTER ON OFF AUDIO CD RECORDER DX-R700 >10 10/0 EDIT/NO oREC sPLAY oREC REC s You can perform digital recording to record the signal input to the digital input terminals or analog recording to record the signal input to the analog input terminals. The recording level can be adjusted manually. 1 Repeatedly press the INPUT button until "Digital In 1", "Digital In 2" or "Analog In" appears. INPUT Types of digital source that can be recorded The DX-R700 contains an internal sampling rate converter, and therefore can record digital signals of the sampling rates given below. · 44. 1 kHz (CDs, etc. ) · 32 kHz (DAT, satellite broadcasts, etc. ) · 48 kHz (DAT, satellite broadcasts, etc. ) Note: When performing a digital recording from HDCDs, DTS CDs, and the like, be sure to set the recording level to 0 dB (see page 21). or or Proceed to step 3 if you do not wish to adjust the recording level Note: Verify to which digital input the optical digital cable is connected. Preparation · Turn on the DX-R700 (see page 16). · Place a recordable CD-R or CD-RW in the DXR700 (see page 17). · Verify that the input dial and recording selection button of the amplifier are set to the position of the recording source. 2 Start playback of the recording source. 3 Press the o REC button. The level sync function is set to On (see page 26). "Rec setup" appears in the display followed by the time display (the recording standby state). DX-R700 REC RC-448C REC Proceed to step 6 if you do not wish to adjust the recording level. Note: When you select the digital input but the digital cable is not connected to the DX-R700, "D. InUnlock" will appear. 20 Digital recording/Analog recording 4 Adjust the recording level. (1) Press the EDIT/NO button and turn the MULTI JOG dial until "Rec Level?" appears. MULTI JOG EDIT/ NO (4) After adjusting the recording level, press the MULTI JOG dial. Pressing the YES button provides the same operation. MULTI JOG PUSH TO ENTER PUSH TO ENTER 5 Stop the playback of the recording (2) Press the MULTI JOG dial. Pressing the YES button provides the same operation. Press the EDIT/NO button if you cancel the adjustment operation. source. 6 Press the s button and start the recording source. Recording starts. The track numbers are automatically recorded. After the recording reaches the end of the disc, the DX-R700 will stop. (3) Turn the MULTI JOG dial to adjust the recording level as desired. The current level is displayed, ranging from - to +20 dB. MULTI JOG To set the track numbers manually Press the o REC button. To pause the recording PUSH TO ENTER For analog recording Adjust so that when the recording level is at its highest, it does not reach "OVER" in the front display. If OVER is reached, the sound becomes distorted. Adjust the level so that "OVER" will not light. Press the g button. To resume recording, press the s button when the time display appears. If the entire disc becomes filled with recordings, the DX-R700 automatically stops. To stop the recording Press the e button. Notes: · When digitally recording satellite broadcasts, the track numbers may not be assigned properly. If this occurs, turn off the level sync function and set the track numbers manually (see page 26). · If the time between tracks is extremely short, the track numbers may not be assigned properly. L 40 20 10 4 2 0 OVER R For digital recording Adjust so that when the recording level is at its highest, the peak level should indicate between -6 dB and -2 dB in the front display. Adjust the level so that this range should light. L 40 20 10 4 2 0 OVER R Even if you change the recording level, the monitor sound level from the DIGITAL OUT terminals will not change. 21 Synchronous recording by input signal detection (Signal synchronous recording) oREC STANDBY/ ON OPEN / CLOSE RANDOM MEMORY REPEAT ABC DUAL DIGITAL INPUT STANDBY/ON PAUSE STOP PLAY DEF 3 NAME 1 2 GHI 4 MEMORY STANDBY CLEAR DISPLAY MULTI JOG INPUT JKL 5 MNO 6 SCROLL PQRS PHONES REPEAT FINALIZE EDIT/ NO PUSH TO ENTER TUV 8 W XYZ 9 CLEAR PHONES LEVEL POWER YES 7 REC DISPLAY MIN MAX ENTER ON OFF AUDIO CD RECORDER DX-R700 >10 10/0 oREC INPUT REC This method allows you to start recording in synchronization with the input signals from the Onkyo products that are not equipped with an z connector or other manufacturer's products. When recording with the Onkyo products equipped with an z connector, refer to "Synchronous recording" on page 24. [. . . ] Either turn off the television or move the DX-R700 away from the television. Adjust the recording level to a proper level (see page 21). Replace all the remote controller batteries with new batteries (see page 11). Remove the obstructing object (see page 11). [. . . ]