User manual ONKYO ED-301

[. . . ] Contents Important Safeguards 2 Digital Surround Processor Precautions 3 ED-301 Instruction Manual POWER PARAMETER CONTROLLER INPUT-1 INPUT-2 LISTENING MODE CINEMA Re-EQ Features 4 Before using this unit 5 System configuration 6 Connections 7-9 ON OFF TEST TONE DIMMER SPEAKER DISTANCE LEVEL MULTI-CH INPUT MIDNIGHT THEATER LFE LEVEL VOLUME Speaker setting and distance setting 10-11 DIGITAL SURROUND PROCESSOR ED-301 Output level setting 12-13 Playing surround sounds 14-15 Thank you for purchasing the ONKYO ED-301 Digital Surround Processor. Please read this manual thoroughly before making connections and turning on the unit. Following the instructions in this manual will enable you to obtain the optimum performance and maximum listening enjoyment from your new ED-301. Please retain this manual for future reference. Setting the listening mode 16-17 Position and name of each control 18 Troubleshooting 19 Specifications 20 WARNING "TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. " WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION "TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] If your ED-301 is connected to an A/V amplifier with 5. 1-channel audio input, also perform speaker setting on the A/V amplifier. Speaker setting procedure 1 3 2 Speaker setting Set one of the following parameters for each speaker type. For a typical speaker system with six speakers, set "LARGE/SMALL" or "YES" for all speaker types. Set this parameter if the connected speaker(s) can cover the bass range. SMALL Set this parameter if the connected speaker(s) cannot cover the bass range. YES Set this parameter if you connect a center speaker, surround speakers, or a subwoofer. NONE or NO Set this parameter if there is no speaker connected to that channel and output is to be made to other speakers. Available combination of setting for each speaker type Speaker type SW (Subwoofer) L/R (Front) C (Center) LS/RS (Surround) SMALL LARGE 3 1 2 Press POWER. Skip this step if the desired input mode is already selected. Do not press MULTI-CH INPUT or you will be unable to go on to the next and later steps. Press SPEAKER repeatedly to select the speaker type for the speaker you are setting and then press PARAMETER CONTROLLER repeatedly to select the parameter you want to set. Each time you press the SPEAKER button, the speaker indicator(s) that is blinking changes as follows. SW (Subwoofer) L/R (L/R Front) C (Center) LS/RS (L/R Surround) COMPLETE Speaker setting indication 3 Possible parameter setting YES LARGE NO Setting LARGE automatically brings up selection for next speaker type. YES/NO LARGE/SMALL/ LARGE/SMALL/NONE NONE YES/NO LARGE/SMALL/ LARGE/SMALL/NONE NONE INPUT-1 DOLBY DIGITAL L R Note: The following is the factory-set parameter for each speaker type: SW : YES L/R : SMALL C : YES LS/RS : YES Indicator for speaker(s) being set When the setting for the current speaker type has been done, press SPEAKER and the speaker indicator(s) for the next speaker type will blink. You will get out of the speaker setting mode if the speaker setting operation is interrupted for 3 seconds or longer. To return to the speaker setting mode in this case, press the SPEAKER button again. Speaker setting and listening mode If system includes Surround speakers but lacks a Center speaker. . . PHANTOM mode L C R L If system includes a Center speaker but lacks Surround speakers. . . 3 STEREO mode C R If system lacks both a Center and Surround speakers. . . STEREO mode L C R LS RS LS RS LS RS SW L/R C LS/RS : YES or NO : SMALL or LARGE : NO or NONE : SMALL or LARGE SW L/R C LS/RS : YES or NO : SMALL or LARGE : YES, or SMALL or LARGE : NO or NONE SW L/R C LS/RS : YES or NO : SMALL or LARGE : NO or NONE : NO or NONE 10 Speaker setting and distance setting Distance setting procedure Distance setting For each speaker type, set the distance from your listening position to where the speaker is located. 1 4 2 Left Front speaker Center speaker Right Front speaker 3 L C R Subwoofer 1 2 Left Surround speaker LS Listening position RS Right Surround speaker 3 Press POWER. Skip this step if the desired input mode is already selected. Do not press MULTI-CH INPUT or you will not be able to go to the next and later steps. Press DISTANCE repeatedly to select the speaker type for which you are setting the distance and then press PARAMETER CONTROLLER to display the parameter you want to set. Each time you press the DISTANCE button, the speaker indicator(s) that is blinking changes as follows. L/R (L/R Front) C (Center) LS/RS (L/R Surround) COMPLETE Press the PARAMETER CONTROLLER button to display parameter you want to set while the speaker indicator is blinking. L/R: Distance from listening position to L/R Front speaker position. C: Distance from listening position to Center speaker position. LS/RS: Distance from listening position to L/R Surround speaker position. Distance setting indication Indicator for speaker(s) for which setting is being made INPUT-1 DOLBY DIGITAL ft L R Indication in meters Indication in feet The distance setting can be adjusted in units of 1 foot (0. 3 meter). [. . . ] [See page 14, 15] · Adjust the output level by using the unit's VOLUME button and A/V amplifier's master volume control. [See pages 12-15] · Check the encoding method of the input signal. [See page 14] No sound is output. · The input mode selection is incorrect. · The output level is set to "-". · The source signal has a sampling frequency of other than 32 kHz, 44. 1 kHz or 48 kHz. · The source signal format is other than Dolby Digital or PCM format. [. . . ]