User manual ONKYO EQ-100

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] · Choose a higher crossover frequency if you want more sound from your subwoofer. Double Bass On Off Turn this setting on to boost bass output by feeding bass sounds from the front left, right, and center channels to the subwoofer. Note · This function can be set only if the "Subwoofer" setting is set to "Yes", and the "Front" setting is set to "Large" ( page 29). Subwoofer Yes: Select if a subwoofer is connected. No: Select if no subwoofer is connected. Front Small: Large: Select based on the cone diameter. Note · If the "Subwoofer" setting is set to "No", this setting is fixed at "Large" and does not appear. When an optional unit is connected to the UNIVERSAL PORT jack on the AV receiver, the speaker setting menu may appear on-screen. Wireless Front, Wireless Surr (Surround)*1 Yes: The audio is output from the speakers connected to the wireless unit. No: The audio is not output from the speakers connected to the wireless unit. When the wireless unit is connected to the UNIVERSAL PORT jack on the AV receiver, you can select if you wish to output the audio from the speakers connected to the wireless unit. Note · When no wireless unit is connected to the UNIVERSAL PORT jack on the AV receiver, this setting is not available. *1 If the "Surround" setting is set to "None" ( page 29), this setting cannot be selected. Center*1, Surround*1 Small: Large: Select based on the cone diameter. None: Select if no speaker is connected. Note *1 If the "Front" setting is set to "Small", the "Large" option cannot be selected. En 29 Sp Distance (Speaker Distance) Menu Sp Distance Level Cal (Level Calibration) Menu Level Cal Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arrives at the listener's ears as the sound designer intended. Note · These settings are disabled when: ­ a pair of headphones is connected, or ­ the "Audio TV Out" setting is set to "On" ( page 35), or ­ "HDMI Ctrl (RIHD)" is set to "On" ( page 34) and you're listening through your TV speakers, or ­ Speakers B is on, or ­ Speakers A is off. · Speakers that you set to "No" or "None" in the "Sp Config (Speaker Configuration)" ( page 29) cannot be selected. Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position. Left, Center*1, Right, Surround Right, Surround Left ­12 dB to 0 dB to +12 dB in 1 dB step. Subwoofer*1 ­15 dB to 0 dB to +12 dB in 1 dB step. If the stereo image feels too wide, or there's too much surround sound, move the sound field forward to improve the balance. Conversely, if the stereo image feels like it's in mono, or there's not enough surround sound, move it backward. En 31 Source Setup Menu Source Setup Note · If "Dynamic EQ" setting is set to "Off", these technologies cannot be used. Preparation Press the input selector buttons to select an input source. Audyssey Dynamic EQ Off On: Audyssey Dynamic EQ® becomes active. The Dynamic EQ indicator will light ( page 8). With Audyssey Dynamic EQ, you can enjoy great sound even when listening at low volume levels. Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. It does so by selecting the correct frequency response and surround volume levels moment-by-moment so that the content sounds the way it was created at any volume level -- not just at reference level. Note · These technologies cannot be used when: ­ a pair of headphones is connected, or ­ Direct listening mode is selected, or ­ Speakers B is on, or ­ Speakers A is off. Dynamic Volume Off Light: Light Compression Mode becomes active. Medium: Medium Compression Mode becomes active. Heavy: Heavy Compression Mode becomes active. It quiets the loud parts, such as explosions, and boosts the quiet parts so they can be heard. Note · If you make Dynamic Volume active, "Dynamic EQ" setting is set to "On". The Dynamic Vol indicator will light ( page 8). · These technologies cannot be used when: ­ a pair of headphones is connected, or ­ Direct listening mode is selected, or ­ Speakers B is on, or ­ Speakers A is off. [. . . ] Connect the HDMI OUT jack to the HDMI input jack of the TV. Blu-ray Disc/DVD player, etc. HDMI connection AV receiver DIGITAL AUDIO connection (OPTICAL) HDMI connection TV, projector, etc. 2. Connect the audio output from the TV to the OPTICAL IN 2 jack of the AV receiver using an optical digital cable. Note · When the audio return channel (ARC) function is used with an ARC capable TV, this connection is not necessary ( page 35). Confirm the settings. Turn on the power for all connected components. Turn off the power of the TV, and confirm that the power of the connected components is turned off automatically with the link operation. [. . . ]