User manual ONKYO EQ-18

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] Listening Mode You can select the listening modes that are grouped in the following categories: "MOVIE/TV", "MUSIC" and "GAME". Use / to select the category and / to select the listening mode. Press ENTER to switch to the selected listening mode. Output channel Speakers A: 5. 1 channels Speakers A: 2. 1 channels* Speakers B: 2 channels Speakers B: 2 channels No sound * While Speakers B is on, channels are reduced to 2. 1 in the main room. Tip · Alternatively, you can use the AV receiver's SPEAKERS A and B. Using the Sleep Timer With the sleep timer, you can set the AV receiver to turn off automatically after a specified period. 1 Press RECEIVER followed by SLEEP repeatedly to select the required sleep time. The sleep time can be set from 90 to 10 minutes in 10 minute steps. The SLEEP indicator lights on the display when the sleep timer has been set. The specified sleep time appears on the display for about 5 seconds, then the previous display reappears. Tip · If you need to cancel the sleep timer, press SLEEP repeatedly until the SLEEP indicator goes off. · To check the time remaining until the AV receiver sleeps, press SLEEP. Note that if you press again on SLEEP as the time being displayed is equal or inferior to 10 minutes, the sleep timer will go off. Note *1 Depending on the input source and listening mode, not all channels shown here output the sound. En 29 Setting the Display Brightness You can adjust the brightness of the AV receiver's display. Changing the Input Display When you connect an -capable Onkyo component, you must configure the input display so that can work properly. This setting can be done only from the front panel. 1 Press RECEIVER followed by DIMMER repeatedly to select: dim, dimmer, or normal brightness. 1 2 Displaying Source Information You can display various information about the current input source as follows. Press TV/CD, GAME or VCR/DVR. "TV/CD", "GAME" or "VCR/DVR" appears on the display. Start recording on the VCR and start playback on the camcorder and CD player. The video from the camcorder and the audio from the CD player are recorded by the VCR. 2 3 En 31 Advanced Operations Advanced Setup On-screen Setup Menus The on-screen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receiver's display when changing settings. Note · The on-screen setup menus are displayed when: ­ There is no video input, or ­ The video input is 480p, 576p, 720p, 1080i, or 1080p. Common Procedures in Setup Menu Remote indicator RECEIVER ENTER // / SETUP RETURN Setup Menu 1. HDMI Setup HDMI Input ( page 33) BD/DVD VCR/DVR CBL/SAT GAME AUX TUNER TV/CD BD/DVD VCR/DVR CBL/SAT GAME AUX TUNER TV/CD The on-screen setup menus appear on the connected TV and provide a convenient way to change the AV receiver's various settings. Settings are organized into 10 categories on the main menu. Carry out the settings by using the on-screen display. 1 Press RECEIVER followed by SETUP. Tip · If the main menu doesn't appear, make sure the appropriate external input is selected on your TV. Level Cal ( page 35) Left Center Right Surround Right Surround Left Subwoofer 2 3 Use / to select a menu, and then press ENTER. Use / to select target, and use / to change the setting. Press RETURN to return to the main menu. Component ( page 33) BD/DVD VCR/DVR CBL/SAT GAME AUX TUNER TV/CD Audio Adjust ( page 35) Input Ch (Mux) Input Ch (Mono) Panorama Dimension Center Width Center Image Listening Angle Note · This procedure can also be performed on the AV receiver by using SETUP, arrow buttons, and ENTER. · During Audyssey 2EQ® Room Correction and Speaker Setup, messages, etc. , that are displayed on the TV screen will appear in the Display. Digital Audio ( page 33) BD/DVD VCR/DVR CBL/SAT GAME AUX TUNER TV/CD Source Setup ( page 36) Audyssey Dynamic EQ Reference Level Dynamic Volume A/V Sync Name Audio Selector Fixed Mode Sp Config ( page 34) Subwoofer Front Center Surround Crossover Double Bass Hardware ( page 38) Volume OSD Remote ID AM Freq Step Auto Standby Sp Distance ( page 34) Unit Left Center Right Surround Right Surround Left Subwoofer HDMI Setup ( page 39) HDMI Ctrl (RIHD) HDMI Through Audio TV Out Audio Return Ch LipSync En 32 Explanatory Notes Menu Sp Config Component (Component Video Input) Menu Component Subwoofer Yes: Select if a subwoofer is connected. No: Select if no subwoofer is connected. Menu selection Setting target Setting options (default setting underlined) If you connect a video component to a component video input, you must assign that input to an input selector. [. . . ] Connect the HDMI OUT jack to the HDMI input jack of the TV. Blu-ray Disc/DVD player, etc. HDMI connection AV receiver DIGITAL AUDIO connection (OPTICAL) HDMI connection TV, projector, etc. 2. Connect the audio output from the TV to the OPTICAL IN 2 jack of the AV receiver using an optical digital cable. Note · When the audio return channel (ARC) function is used with an ARC capable TV, this connection is not necessary ( page 40). Confirm the settings. Turn on the power for all connected components. Turn off the power of the TV, and confirm that the power of the connected components is turned off automatically with the link operation. [. . . ]