User manual ONKYO EQ-201

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] See also: · "Audyssey" ( page 39) · "Using the Audio Settings" ( page 43) Info*1 You can view the information of the following items: "Input" and "Output". Listening Mode You can select the listening modes that are grouped in the following categories: "MOVIE/TV", "MUSIC" and "GAME". Use / to select the category and / to select the listening mode. Press ENTER to switch to the selected listening mode. Note *1 Depending on the input source and listening mode, not all channels shown here output the sound. En 31 Setting the Display Brightness You can adjust the brightness of the AV receiver's display. Changing the Input Display When you connect an -capable Onkyo component, you must configure the input display so that can work properly. This setting can be done only from the front panel. 1 Press RECEIVER followed by DIMMER repeatedly to select: dim, dimmer, or normal brightness. Tip · (North American and Brazilian models) Alternatively, you can use the AV receiver's DIMMER. 1 2 Press TV/CD, GAME or VCR/DVR. "TV/CD", "GAME" or "VCR/DVR" appears on the display. Press and hold down the same button (about 3 seconds) to change the input display. Repeat this step to select the desired input display. TV/CD: TV/CD DOCK TAPE Displaying Source Information You can display various information about the current input source as follows. 1 Press RECEIVER followed by DISPLAY repeatedly to cycle through the available information. GAME: GAME DOCK VCR/DVR: VCR/DVR DOCK Note · DOCK cannot be selected for multiple input selectors at the same time. · Enter the appropriate remote control code before using the remote controller for the first time ( page 47). The following information can typically be displayed. Input source & volume*1 Listening mode Signal format*2 or sampling frequency Using the Music Optimizer Tip · Alternatively, you can use the AV receiver's DISPLAY. *1 When AM or FM radio is used, the band, preset number, and frequency are displayed. HDMI Setup HDMI Input ( page 35) BD/DVD VCR/DVR CBL/SAT GAME AUX TUNER TV/CD BD/DVD VCR/DVR CBL/SAT GAME AUX TUNER TV/CD ENTER // / SETUP RETURN Sp Distance ( page 37) Unit Left Front High Left Center Front High Right Right Surround Right SurrBack Right SurrBack Left Surround Left Subwoofer The on-screen setup menus appear on the connected TV and provide a convenient way to change the AV receiver's various settings. Settings are organized into 10 categories on the main menu. Carry out the settings by using the on-screen display. 1 Press RECEIVER followed by SETUP. Tip · If the main menu doesn't appear, make sure the appropriate external input is selected on your TV. Component ( page 35) BD/DVD VCR/DVR CBL/SAT GAME AUX TUNER TV/CD Level Cal ( page 37) Left Front High Left Center Front High Right Right Surround Right SurrBack Right SurrBack Left Surround Left Subwoofer 2 3 Use / to select a menu, and then press ENTER. Use / to select target, and use / to change the setting. Press RETURN to return to the main menu. Digital Audio ( page 35) BD/DVD VCR/DVR CBL/SAT GAME AUX TUNER TV/CD Audio Adjust ( page 37) Input Ch (Mux) Input Ch (Mono) Panorama Dimension Center Width Height Gain Dolby EX Center Image Listening Angle Note · This procedure can also be performed on the AV receiver by using SETUP, arrow buttons, and ENTER. · During Audyssey 2EQ® Room Correction and Speaker Setup, messages, etc. , that are displayed on the TV screen will appear in the Display. Explanatory Notes Menu Sp Config Sp Config ( page 36) Subwoofer Front Center Surround Front High Surround Back Surround Back Ch Crossover Double Bass Source Setup ( page 39) Audyssey Dynamic EQ Reference Level Dynamic Volume A/V Sync Name Audio Selector Fixed Mode Subwoofer Yes No Menu selection Setting target Setting options (default setting underlined) En 34 HDMI Input Menu HDMI Input If you connect a video component to an HDMI input, you must assign that input to an input selector. For example, if you connect your Blu-ray Disc/DVD player to HDMI IN 2, you must assign "HDMI2" to the "BD/DVD" input selector. Here are the default assignments. Input selector BD/DVD VCR/DVR CBL/SAT GAME AUX TV/CD Default assignment HDMI1 HDMI2 HDMI3 HDMI4 --------- BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX, TV/CD IN1, IN2: Select a corresponding component video input that the video component has been connected. - - - - -: Select if you're not using the COMPONENT VIDEO OUT. Digital Audio (Digital Audio Input) Menu Digital Audio If you connect a component to a digital audio input, you must assign that input to an input selector. For example, if you connect your CD player to the OPTICAL IN 1, you must assign "OPTICAL1" to the "TV/CD" input selector. Here are the default assignments. Input selector BD/DVD VCR/DVR CBL/SAT GAME AUX TV/CD Default assignment COAXIAL1 ----COAXIAL2 OPTICAL1 ----OPTICAL2 BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX, TV/CD HDMI1, HDMI2, HDMI3, HDMI4: Select a corresponding HDMI input that the video component has been connected. [. . . ] Connect the HDMI OUT jack to the HDMI input jack of the TV. Blu-ray Disc/DVD player, etc. HDMI connection AV receiver DIGITAL AUDIO connection (OPTICAL) HDMI connection TV, projector, etc. 2. Connect the audio output from the TV to the OPTICAL IN 2 jack of the AV receiver using an optical digital cable. Note · When the audio return channel (ARC) function is used with an ARC capable TV, this connection is not necessary ( page 42). Confirm the settings. Turn on the power for all connected components. Turn off the power of the TV, and confirm that the power of the connected components is turned off automatically with the link operation. [. . . ]