User manual ONKYO HT-S3100

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5. 1ch Home Theater System HT-S3100 HT-S3105 AV Receiver (HT-R340) Speaker Package HTP-360 (North American and Asian models) HTP-318 (European models) Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Turning On & First Time Setup. . . . . 37 Basic Operation Playing your AV components . . . . . . . [. . . ] For example, if you connect your DVD player to DIGITAL IN OPTICAL, you'll need to assign that input (OPT1) to the DVD input source. You can change the assignments as follows. Note: Make sure you also set your digital sources to send out a digital signals. Please refer to the digital sources' manual. 2 TAPE or VIDEO 3 1 DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER Press the input selector button for the source that you want to assign. (Digital inputs cannot be assigned to the TUNER input source. ) CD 2 DIGITAL INPUT Press the [DIGITAL INPUT] button. The current assignment appears. Note: HDD can be selected for the TAPE input selector or VIDEO 3 input selector, but not both at the same time. 3 DIGITAL INPUT Press the [DIGITAL INPUT] button repeatedly to select COAX, OPT1, OPT2, or "­ ­ ­ ­" (analog). 38 For the VIDEO 3 input selector, the setting changes in this order: VIDEO 3 HDD Press and hold down the [TAPE] or [VIDEO 3] input selector button (about 3 seconds) to change the setting. Repeat this step to select MD, CDR, or HDD. For the TAPE input selector, the setting changes in this order: TAPE MD CDR HDD Playing Your AV Components Basic AV Receiver Operation 2 STANDBY/ON DISPLAY TUNING / PRESET 4 MASTER VOLUME ON/STANDBY REMOTE MODE RECEIVER TAPE DVD 1 INPUT SELECTOR 1 1 V1 2 V2 3 V3 CD 4 ENTER STANDBY 5 MULTI CH 6 DVD MD 7 A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP 8 TUNER 9 CD CDR TAPE CLEAR PHONES MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER CD +10 --/--- 0 DIMMER CLR SLEEP HDD DISC ALBUM CH VOL 4 MULTI CH 1 TOP MENU MENU 2 SP A / B MUTING ENTER PLAYLIST PLAYLIST 1 AV receiver DVD VIDEO 1/VCR VIDEO 2 Remote controller RECEIVER Use the AV receiver's input selector buttons to select the input source. To select the input source with the remote controller, press the [RECEIVER] button, and then use the INPUT SELECTOR buttons. On the remote controller, the [V1], [V2], and [V3] buttons select the VIDEO 1/VCR, VIDEO 2, and VIDEO 3 input sources respectively. VIDEO 3 TAPE TUNER V1 CD V2 V3 DVD TAPE TUNER CD 2 AV receiver A SPEAKERS B Remote controller SP A / B Use the SPEAKERS [A] and [B] buttons on the AV receiver or the [SP A/B] button on the remote controller to select the speaker set that you want to use. Pressing the remote controller's [SP A/B] button cycles through the following settings: Speaker Set A Speaker Set A&B Speaker Set B Off. The A and B speaker indicators show Indicators whether each speaker set is on or off. Note that when speaker set B is turned on, speaker set A is reduced to 2. 1-channel playback. 3 4 AV receiver MASTER VOLUME Start playback on the source component. When you select DVD or another video component, on your TV you'll need to select the video input that's connected to the AV receiver's MONITOR OUT. Remote controller VOL To adjust the volume, use the MASTER VOLUME control, or the remote controller's [VOL] button. The AV receiver is designed for home theater enjoyment and has a wide volume range for precise adjustment. Note: The maximum master volume level is affected by the subwoofer volume level. 5 Select a suitable listening mode and enjoy!See "Using the Listening Modes" on page 49. 39 Playing Your AV Components--Continued Using the Multichannel Input You can display various information about the current input source as follows. RECEIVER ON/STANDBY REMOTE MODE RECEIVER 1 V1 RECEIVER TAPE DVD INPUT SELECTOR 2 V2 3 V3 CD DISPLAY MD Press the [RECEIVER] button, and then press the [DISPLAY] button repeatedly to cycle through the available information. MULTI CH 4 7 TAPE 5 MULTI CH 6 DVD 8 TUNER 9 CD CDR +10 --/--- 0 DIMMER CLR SLEEP HDD The following information can typically be displayed for input sources. Input source & volume*1 Signal format*2 or sampling frequency Input source & listening mode DISC ALBUM CH VOL The multichannel input is for connecting a component with individual 5. 1-channel analog audio output jacks, such as a DVD player or MPEG decoder. See page 29 for hookup information. RECEIVER Press the [RECEIVER] button followed by the [MULTI CH] button so that MULTI CH indicator appears on the display. Audio from the multichannel input will now be used for the DVD input source. MULTI CH indicator MULTI CH Note: · While the multichannel input is selected, the Speaker Configuration settings on page 55 are ignored, and signals from the multichannel input are fed to the front left, front right, center, surround left, and surround right speakers and subwoofer regardless of those settings. *1 When AM or FM radio is used, the band, preset number, and frequency are displayed. *2 If the input signal is analog, or AM or FM radio is selected, no format information is displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not PCM, the signal format is displayed. [. . . ] The AV receiver's remote controller doesn't control your iPod · 3rd generation iPods are not supported. · Make sure your iPod is properly inserted in the RI Dock. If your iPod is in a case, it may not connect Others The sound changes when I connect my headphones?· When a pair of headphones is connected, the listening mode is set to Stereo, unless it's already set to Stereo, Mono, Direct. [. . . ]