User manual ONKYO HT-S3200

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5. 1ch Home Theater System Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 HT-S3200 AV Receiver (HT-R370) Speaker Package (HTP-370) Turning On & First Time Setup . . . 35 Basic Operations. . . . . . . . . . . . . . . . . . . . . . . . . 38 Instruction Manual Using the Listening Modes . . . . . . . . 47 Advanced Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Controlling Other Components. . . 60 Others. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Thank you for purchasing an Onkyo 5. 1ch Home Theater System. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new 5. 1ch Home Theater System. Please retain this manual for future reference. En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] Tip: This procedure can also be performed on the remote controller by using [AUDIO] button (see page 59). Note: The Music Optimizer function only works with PCM digital audio input signals with a sampling rate below 48 kHz and analog audio input signals. The Music Optimizer is disabled when the Direct listening mode is selected. Specifying the Digital Signal Format The following table shows the display indicator for each digital signal format. Format Dolby Digital DTS PCM PCM Display Normally, the AV receiver detects the format of digital input signals automatically. However, if you experience either of the following issues when playing PCM or DTS sources, you can specify the signal format manually. · If the beginnings of tracks from a PCM source are cut off, try the PCM setting. · If noise is produced when fast forwarding or rewinding a DTS CD, try the DTS setting. , AUDIO 1 Press and hold [AUDIO] button for about 8 seconds. 2 While "Auto" is displayed (about 3 seconds), use the Left and Right [ ]/[ ] buttons to select: PCM, DTS, or Auto. PCM: Only 2-channel PCM format input signals will be heard. If the input signal is not PCM, the PCM indicator will flash and there will be no sound. DTS: Only DTS format input signals will be heard. If the input signal is not DTS, the DTS indicator will flash and there will be no sound. Auto (default): The format is detected automatically. If no digital input signal is present, the corresponding analog input is used instead. 41 Listening to the Radio AM/FM Frequency Step Setup 4 RECEIVER ENTER SETUP Use the Left and Right [ ]/[ ] buttons to select: (North American/Taiwan models) 200k/10k: Select if 200k/10k steps are used in your area. 50k/9k: Select if 50k/9k steps are used in your area. (Asian models) 10kHz: Select if 10kHz steps are used in your area. 9kHz: Select if 9kHz steps are used in your area. Setup closes. For AM/FM tuning to work properly, you must specify the AM/FM frequency step used in your area. Note that when this setting is changed, all radio presets are deleted. 5 1 Press the [RECEIVER] button, followed by the [SETUP] button. Note: This procedure can also be performed on the AV receiver by using its [SETUP] button, arrow buttons, and [ENTER] button. 2 Use the Up and Down [ ]/[ ] buttons to select "8. Hardware", and then press [ENTER]. 3 Use the Up and Down [ ]/[ ] buttons to select "FM/AM" (North American/Taiwan models) or "AM Freq" (Asian models). (North American/Taiwan models) (Asian models) 42 Listening to the Radio--Continued Listening to AM/FM Stations AM TUNING Manual Tuning Mode 1 Press the [TUNING MODE] button so that the AUTO indicator disappears from the display. 2 FM TUNING MODE With the built-in tuner, you can enjoy AM and FM radio stations and store your favorite stations as presets for easy selection. Use the [AM] or [FM] input selector button to select "AM" or "FM". In this example, FM has been selected. or Band Frequency Press and hold the TUNING Up or Down [ ]/[ ] button. The frequency stops changing when you release the button. Press the button repeatedly to change the frequency one step at a time. The North American model changes FM frequency in 0. 2MHz steps, 10kHz steps for AM. [. . . ] The functions don't work · To use , you must make an connection and an analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally (page 34). The following settings can be made for the composite video inputs You must use the buttons on the unit to make these settings. While holding down the input selector button for the input source that you want to set, press the [SETUP] button. Use the Left and Right [ ]/[ ] buttons to change the setting. [. . . ]