User manual ONKYO HT-S4100

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5. 1ch Home Theater System HT-S4100 AV Receiver (TX-SR304) Front Speakers (SKF-360F L/R) Center Speaker (SKC-360C) Surround Speakers (SKM-360S L/R) Subwoofer (SKW-460) Remote Interactive Dock (DS-A1XP) Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Turning On & First Time Setup. . . . . 36 Basic Operation Playing your AV components . . . . . . . [. . . ] The crossover frequency can be Cone diameter changed on page 55. DISC ALBUM CH VOL GUIDE TOP MENU PREVIOUS MENU 1 RECEIVER Press the [RECEIVER] button followed by the [SETUP] button. SP A / B MUTING 2­8 PLAYLIST ENTER PLAYLIST RETURN RETURN SETUP 1, 9 SETUP 2 LISTENING MODE STEREO SURROUND AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE DISPLAY L NIGHT CINE FLTR LEVELLEVEL+ Use the Up and Down [ ]/[ ] buttons to select "1. SP Config, " and then press the [ENTER] button. ENTER RC-645S 3 Speaker Configuration setting only need to be changed if you're not using the speakers in this package. These settings cannot be changed while headphones are connected, speaker set B is on, or the multichannel DVD input is being used. While the Subwoofer setting is selected, use the Left and Right [ ]/[ ] buttons to select Yes or No. Yes: Select if a subwoofer is connected. No: Select if no subwoofer is connected. Use the Down [ ] button to select "Front, " and then use the Left and Right [ ]/[ ] buttons to select Small or Large. Small: Select if the front speakers are small. Large: Select if the front speakers are large. Note: · If the Subwoofer setting in step 3 is set to No, this setting is fixed at Large and does not appear. 4 38 First Time Setup--Continued 5 Use the Down [ ] button to select "Center, " and then use the Left and Right [ ]/[ ] buttons to select Small, Large, or None. Small: Select if the center speaker is small. Large: Select if the center speaker is large. None: Select if no center speaker is connected. Note: · If the Front setting in step 4 is set to Small, the Large option cannot be selected. Testing the speakers To test that all of the speakers are working properly, press the remote controller's [TEST TONE] button. LISTENING MODE STEREO SURROUND AUDIO SUBTITLE RANDOM REPEAT TEST TONE TEST TONE CH SEL PLAY MODE LEVEL- LEVEL+ DISPLAY L NIGHT CINE FLTR RC-645S 6 Use the Down [ ] button to select "Surround, " and then use the Left and Right [ ]/[ ] buttons to select Small, Large, or None. Small: Select if the surround speakers are small. Large: Select if the surround speakers are large. None: Select if no surround speakers are connected. Note: · If the Front setting in step 4 is set to Small, the Large option cannot be selected. The test tone will be output by each speaker in turn and the name of each speaker will appear on the display. To turn off the test tone, press the [TEST TONE] button again. · If the test tone is not produced by a speaker, or it's produced by a speaker other than that shown on the display, you may have wired the speakers incorrectly and you should check your connections (see pages 21, 22). · If the test tone is not produced by a speaker and its name does not appear on the display, you may have set the speaker settings incorrectly (see page 38). 7 SETUP Press the [SETUP] button. When you want to go back up one menu level to "SP Config, " press the [RETURN] button. 39 Playing Your AV Components Basic AV Receiver Operation ON/STANDBY REMOTE MODE RECEIVER TAPE DVD 1 Subwoofer's rear panel 2 STANDBY/ON STANDBY DISPLAY TUNING / PRESET 4 MASTER VOLUME ENTER 1 INPUT SELECTOR 1 V1 2 V2 3 V3 CD 4 7 TAPE 5 MULTI CH 6 DVD MD 8 TUNER 9 CD CDR +10 --/--TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP 0 DIMMER CLR SLEEP HDD A SPEAKERS B CLEAR PHONES MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER CD DISC ALBUM CH VOL 4 4 MIN MAX MULTI CH 1 2 GUIDE TOP MENU PREVIOUS MENU OUTPUT LEVEL SP A / B MUTING ENTER PLAYLIST PLAYLIST 1 AV receiver DVD VIDEO 1/VCR VIDEO 2 Remote controller RECEIVER Use the AV receiver's input selector buttons to select the input source. To select the input source with the remote controller, press the [RECEIVER] button, and then use the INPUT SELECTOR buttons. [. . . ] · When a pair of headphones is connected, the listening mode is set to Stereo, unless it's already set to Stereo, Mono, Direct. How do I change the language of a multiplex source?· Use the "Multiplex" setting on the "4. Audio Adjust" menu to select Main or Sub (page 52). [. . . ]