User manual ONKYO HT-S6100

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 7. 1ch Home Theater System HT-S6100 AV Receiver (HT-R667) Speaker Package (HTP-750X) Front Speakers (SKF-750XF L/R) Center Speaker (SKC-750XC) Surround Speakers (SKM-750XS L/R) Surround Back Speakers (SKB-750X L/R) Subwoofer (SKW-750X) Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Turning On & First Time Setup. . . . . 41 Dock for iPod (DS-A1L) Basic Operation Playing your AV components . . . . . . . [. . . ] You can also use the AV receiver's [DIMMER] button. To cancel the sleep timer, press the [SLEEP] button repeatedly until the SLEEP indicator disappears. To check the remaining sleep time, press the [SLEEP] button. Note that if you press the [SLEEP] button while the sleep time is being displayed, you'll shorten the sleep time by 10 minutes. AV receiver DIMMER 51 Common Functions--Continued 7Using Headphones For private listening, you can connect a pair of stereo headphones (1/4-inch phone plug) to the AV receiver's PHONES jack. Displaying Source Information You can display various information about the current input source as follows. Press the [RECEIVER] REMOTE MODE button, and then press the [DISPLAY] button repeatedly to cycle through the available information. ON/STANDBY STANDBY DOCK MULTI CH PHONES A SPEAKERS B Notes: · Always turn down the volume before connecting your headphones. · While the headphones plug is inserted in the PHONES jack, the speakers set A and B are turned off. · When you connect a pair of headphones, the listening mode is set to Stereo, unless it was already set to Mono, Stereo, or Direct, in which case it stays the same. · When the multichannel DVD input is selected, only the front left and front right channels can be heard in the headphones. Note: · This procedure can also be performed on the AV receiver by using its [DISPLAY] button. The following information can typically be displayed: Input source & volume*1 Signal format*2 or sampling frequency Input source & listening mode *1 When AM or FM radio is used, the band, preset number, and frequency are displayed. *2 If the input signal is analog, or AM or FM radio is selected, no format information is displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about 3 seconds, then the previous display reappears. 52 Common Functions--Continued Specifying the Digital Signal Format The following table shows the display indicator for each digital signal format. Format Dolby Digital DTS PCM PCM Display Normally, the AV receiver detects the format of digital input signals automatically. However, if you experience either of the following issues when playing PCM or DTS sources, you can specify the signal format manually. · If the beginnings of tracks from a PCM source are cut off, try the PCM setting. · If noise is produced when fast forwarding or rewinding a DTS CD, try the DTS setting. MASTER VOLUME ON/STANDBY TUNING PRESET STANDBY ENTER DOCK MULTI CH DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP RETURN AUX INPUT PHONES SETUP MIC VIDEO L AUDIO R A SPEAKERS B TONE MOVIE/TV MUSIC GAME DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE LISTENING MODE CLEAR AV RECEIVER HT-R667 DIGITAL INPUT 1 DIGITAL INPUT Press and hold the AV receiver's [DIGITAL INPUT] button for about 3 seconds. 2 DIGITAL INPUT While "Auto" is displayed (about 3 seconds), press the [DIGITAL INPUT] button repeatedly to select: PCM, DTS, or Auto. PCM: Only 2-channel PCM format input signals will be heard. If the input signal is not PCM, the PCM indicator will flash and there will be no sound. DTS: Only DTS (but not DTS-HD) format input signals will be heard. If the input signal is not DTS, the DTS indicator will flash and there will be no sound. Auto (default): The format is detected automatically. If no digital input signal is present, the corresponding analog input is used instead. 53 Listening to the Radio Listening to AM/FM Stations TUNER ON/STANDBY TUNING Manual Tuning Mode TUNING MASTER VOLUME PRESET 1 TUNING MODE Press the [TUNING MODE] button so that the AUTO indicator disappears from the display. STANDBY ENTER DOCK MULTI CH DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP RETURN AUX INPUT PHONES SETUP MIC VIDEO L AUDIO R A SPEAKERS B TONE MOVIE/TV MUSIC GAME DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE LISTENING MODE CLEAR AV RECEIVER HT-R667 2 TUNING TUNING MODE With the built-in tuner, you can enjoy AM and FM radio stations and store your favorite stations as presets for easy selection. Use the [TUNER] input selector button to select AM or FM. [. . . ] If the video source is connected to an S-Video input, connect your TV to an S-Video output. If the video source is connected to a composite video input, connect your TV to a composite video output. Input Assign, " and then select "1. HDMI Input. " Select the relevant input selector, and assign it to "-----" (page 46). [. . . ]