User manual ONKYO HT-S670

[. . . ] Contents Before using AV Receiver HT-R420 Instruction Manual Important safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Supplied accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press MEMORY. The radio station is registered to the preset channel. To register another preset station, repeat steps 1 to 4. Erasing a preset station 1. Select the preset channel you wish to erase. 2. Press FM MODE while holding down MEMORY. The selected preset channel will be erased. 23 Various functions common to all the sources Before operating the SP A/SP B SPEAKERS A/B SP A/SP B Press RCVR/TAPE. This button may be in a slightly different position on your remote controller. MUTING PHONES jack Turning on/off the speaker system A/B You can turn on or off the speaker systems connected to the speaker system A and speaker system B connectors individually. Before operating the remote controller, press RCVR/TAPE. Muting the sound (remote controller only) Press MUTING. The MUTING indicator flashes in the display during the muting mode. Press SPEAKER A on the unit or SP A on the remote controller to turn on or off the speaker system A. Press SPEAKER B on the unit or SP B on the remote controller to turn on or off the speaker system B. Note If you turn on the speaker system B, the speaker system A also reproduces stereo sound automatically. (When a listening mode other than "Direct" is selected, the listening mode is set to "Stereo. ") The lit (speaker) A/B indicators indicate the corresponding speaker systems are on. To restore the sound, press MUTING again. Tip If you turn off the unit during muting, and turn it on again, the sound will be restored. Listening through headphones Connect the plug of the stereo headphones to the PHONES jack on the AV Receiver. Notes · The speakers will not reproduce sound while headphones are connected. · When a listening mode other than "Direct" is selected, the listening mode is set to "Stereo" after connecting the headphones to the PHONES jack. When you disconnect the headphones, the listening mode returns to the previous mode. · When the multi channel input is selected, only the sound of front L/R channel is heard. Press AUDIO SELECTOR (or AUDIO SEL) to select a mode other than "Multich". 24 Various functions common to all the sources DIMMER SLEEP DISPLAY DIMMER These buttons may be in a slightly different position on your remote controller. Changing the display Press DISPLAY. Each time you press DISPLAY, the screen changes as follows: When an input source other than FM or AM is selected Input source + volume Controlling the brightness of the display on the AV Receiver Press DIMMER. Each press of the button changes the brightness as follows: The display becomes less bright. The display becomes bright. Program format* Input source + Listening mode (or Multich) Using the sleep timer (remote controller only) Press SLEEP. "Sleep 90 min" appears in the multipurpose display for about 5 seconds, which means the AV Receiver will turn off and enter standby mode in 90 minutes. Also the SLEEP indicator is lit in the display while the sleep timer is on. SLEEP indicator Press DISPLAY once to initiate the program format display. Pressing the button again switches the display to the other display. * When the input signal is digital audio The program format is displayed. For example, the display "Dolby D: 3/2. 1" shows that the format is Dolby Digital with 5. 1 discrete channels consisting of three front channels (front left, front right, and center), two surround channels (surround left and surround right), and the low frequency effect (LFE) channel. When the front channel number is 2, they are the front left and front right; when it is 1, it is monaural. When the surround channel number is 1, it is monaural; when it is 0, there is no surround channel. When no LFE number is given there is no LFE channel. Also, if there is no program format for the input signal, nothing will be displayed. [. . . ] · There is a tall building or a mountain nearby. [The waves transmitted from the transmission center (direct waves) and the waved reflected by buildings or mountains (diffraction waves) interfere with each other causing multi pass distortion. ] · The power cord is unplugged for a long time. · The sound system you are trying to record is DTS or Dolby Digital surround. · Playback source is not Dolby Digital encoded. [. . . ]