User manual ONKYO HT-SR800

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 7. 1ch Home Theater System HT-SR800 AV Receiver (HT-R550) Front Speakers (SKF-550F) Center Speaker (SKC-550C) Surround Speakers (SKM-550S) Surround Back Speakers (SKB-550) Powered Subwoofer (SKW-550) Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Turning On & First Time Setup. . . . . 36 Instruction Manual Basic Operation Playing your AV components . . . . . . . [. . . ] No: Select if you're not using the HDMI OUT. HDMI video Input 4 SETUP Press the [SETUP] button. Setup closes. 40 First Time Setup--Continued Digital Audio Input Setup Changing the Input Display If you connect an -capable Onkyo MiniDisc recorder, CD recorder, or RI Dock to the TAPE IN/OUT or CBL/SAT IN jacks, for to work properly, you must change this setting. This setting can only be changed on the AV receiver. 1 STANDBY/ON STANDBY 2, 3 MASTER VOLUME TUNING PRESET MULTI CH DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP ENTER RETURN AUX INPUT PHONES SETUP MIC VIDEO L AUDIO R A SPEAKERS B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE CLEAR 1, 2 STANDBY/ON 1, 2 MASTER VOLUME TUNING PRESET To enjoy Dolby Digital and DTS, you must connect your DVD player to the AV receiver digitally (coaxial or optical). These are the default digital audio input assignments. Input selector DVD VCR/DVR CBL/SAT TAPE CD AUX Default assignment COAX 1 OPT 1 COAX 2 ---OPT 2 ---- STANDBY MULTI CH DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP ENTER RETURN AUX INPUT PHONES SETUP MIC VIDEO L AUDIO R A SPEAKERS B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE CLEAR 1 TAPE Press the [TAPE] or [CBL/SAT] input selector button so that "TAPE" or "CBL/SAT" appears on the display. or You can change the digital audio input assignments if necessary. For example, if you connect your DVD player to the OPTICAL 1 DIGITAL IN (OPT1), you must assign that input to the DVD input selector, as follows. CBL/SAT 1 DVD VCR/DVR CBL/SAT AUX TAPE Press the input selector button for the input selector that you want to assign. (Digital inputs cannot be assigned to the TUNER input selector. ) 2 TAPE or CD CBL/SAT Press and hold down the [TAPE] or [CBL/SAT] input selector button (about 2 seconds) to change the setting. Repeat this step to select MD, CDR, or DOCK. For the TAPE input selector, the setting changes in this order: TAPE MD CDR DOCK For the CBL/SAT input selector, the setting changes in this order: CBL/SAT DOCK 2 DIGITAL INPUT Press the [DIGITAL INPUT] button. The current assignment appears. 3 DIGITAL INPUT Press the [DIGITAL INPUT] button repeatedly to select COAX1, COAX2, OPT1, OPT2, or "­ ­ ­ ­" (analog). Note: DOCK can be selected for the TAPE input selector or CBL/SAT input selector, but not both at the same time. Note: Make sure that components connected digitally are configured to output digital audio. Refer to the relevant manuals. 41 Playing Your AV Components Basic AV Receiver Operation MULTI CH 1 TUNING PRESET 4 MASTER VOLUME STANDBY/ON REMOTE MODE RECEIVER TAPE/AMP DVD M D/CDR 1 Subwoofer's rear panel 1 INPUT SELECTOR 1 VCR/DVR 2 CBL/SAT 3 6 DVD CD DOCK STANDBY/ON 4 AUX 5 MULTI CH TV STANDBY 7 TAPE 8 TUNER 9 CD VCR 12 CABLE 10 MULTI CH DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP ENTER RETURN 11 +10 D TUN AUX INPUT 0 ENT DIMMER CLR SLEEP SAT --/--R PHONES SETUP MIC VIDEO L AUDIO 4 4 MIN MAX A SPEAKERS B TONE STEREO LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE CLEAR TV INPUT GUIDE TOP MENU VOL DISC ALBUM CH VOL 2 DISPLAY 2 PREVIOUS MENU OUTPUT LEVEL SP A / B MUTING ENTER PLAYLIST/CAT PLAYLIST/CAT 1 AV receiver DVD VCR/DVR CBL/SAT Remote controller RECEIVER Use the AV receiver's input selector buttons to select the input source. To select the input source with the remote controller, press the [RECEIVER] REMOTE MODE button, and then use the INPUT SELECTOR buttons. 1 AUX TAPE TUNER VCR/DVR 2 CBL/SAT 4 CD AUX 6 DVD 7 TAPE 8 TUNER 9 CD 2 AV receiver A SPEAKERS B Remote controller To turn the speakers on or off, use the AV receiver's SPEAKERS [A] and [B] buttons, or use the remote controller's [SP A/B] button. Pressing the remote controller's [SP A/B] button cycles through the following settings: Speaker Set A Speaker Set A&B Speaker Set B Off. Note that while speaker set B is on, speaker set A is reduced to 5. 1-channel Indicators playback. See page 5 for more information about speaker sets A and B. 3 Start playback on the source component. To watch a DVD or other video source, on your TV, select the video input that's connected to the AV receiver's MONITOR OUT jack. If your TV is connected to the HDMI OUT, see the tip on page 29. Remote controller 4 AV receiver MASTER VOLUME VOL To adjust the volume, use the MASTER VOLUME control, or the remote controller's [VOL] button. The volume can be set to MIN, 1 through 79, or MAX. Since the AV receiver is designed for home theater enjoyment, it has a wide volume range for precise adjustment. To set the level of the subwoofer, use the OUTPUT LEVEL control. Because our ears are less sensitive to very low bass sounds, there's a temptation to set the level of the subwoofer too high. As a rule of thumb, set the subwoofer level to what you think is the optimal level, and then back it off slightly. 5 42 Select a suitable listening mode and enjoy!See "Using the Listening Modes" on page 48. Playing Your AV Components--Continued Displaying Source Information STANDBY/ON REMOTE MODE RECEIVER TAPE/AMP DVD M D/CDR RECEIVER INPUT SELECTOR You can display various information about the current input source as follows. RECEIVER 1 VCR/DVR 2 CBL/SAT 3 6 DVD CD DOCK MULTI CH 4 AUX 5 MULTI CH TV 7 TAPE 8 TUNER 9 CD VCR 12 CABLE 10 11 +10 D TUN 0 ENT DIMMER CLR SLEEP SAT --/--- DISPLAY VOL Press the [RECEIVER] REMOTE MODE button, and then press the [DISPLAY] button repeatedly to cycle through the available information. TV VOL DISC ALBUM CH The following information can typically be displayed: LISTENING MODE STEREO SURROUND AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE LEVELLEVEL+ Input source & volume*1 Signal format*2 or sampling frequency Input source & listening mode DISPLAY DISPLAY VCR L NIGHT DVD CINE FLTR HDD RC-681M Using the Multichannel DVD Input The multichannel DVD input is for connecting a component with a 7. 1-channel analog audio output, such as a DVD-Audio or SACD-capable DVD player, or an MPEG decoder. [. . . ] · If you've connected an -capable Onkyo MD recorder, CD recorder, or RI Dock to the TAPE IN/OUT jacks or CBL/SAT jacks, for the remote controller to work properly, you must set the Input Display to MD, CDR, or DOCK (page 41). · The entered remote control code may not be correct. If more than one code is listed, try each one. · With some AV components, certain buttons may not work as expected, and some may not work at all. [. . . ]