User manual ONKYO HTP-103E

[. . . ] Please retain this manual for future reference. Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Precaution on use . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] Check for the ASTA mark or the BSI mark on the body of the fuse. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMPERE SOCKET. If in any doubt, consult a qualified electrician. Power WARNING BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY. AC outlet voltages vary from country to country. Make sure that the voltage in your area meets the voltage requirements printed on this unit's rear panel (e. g. , AC 230-240 V, 50 Hz). AC Fuse The fuse is located inside the chassis and is not userserviceable. If power does not come on, contact your Onkyo authorized service station. Never Touch this Unit with Wet Hands Never handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by your Onkyo authorized service station. Care Occasionally, you should dust this unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Do not use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel lettering. Declaration of Conformity We, ONKYO EUROPE ELECTRONICS GmbH LIEGNITZERSTRASSE 6, 82194 GROEBENZELL, GERMANY declare in own responsibility, that the ONKYO product described in this instruction manual is in compliance with the corresponding technical standards such as EN60065, EN55013, EN55020 and EN61000-3-2, -3-3. MORI ONKYO EUROPE ELECTRONICS GmbH 3 SKW-150X I Rear Panel Powered subwoofer Control positions and names POWERED SUBWOOFER MODEL NO. SKW-150X 1 POWER switch and indicator To turn on the SKW-150X, set the POWER switch to the ON position (the indicator lights up). To turn off the SKW-150X, set the POWER switch to the OFF position (the indicator goes out). Red: The unit is in standby mode Green: The unit is in operation mode POWER OUTPUT LEVEL LINE INPUT MIN MAX RED : STANDBY GREEN : ON ON OFF The SKW-150X automatically turns to STANDBY mode when no signal has been input for about 20 minutes. The SKW-150X automatically enters operation mode when a signal is input during STANDBY mode. 2 OUTPUT LEVEL knob Use this knob to adjust the output level of the subwoofer. 3 LINE INPUT jack Connect this jack to the subwoofer pre-out of the receiver. 2 3 1 To AC outlet Note: The auto standby function operates on the existence or absence of a constant level input signal. If the auto standby function does not operate properly, try slightly increasing (or decreasing) the subwoofer output level of the receiver. Connection For safety reasons, be sure to unplug the power cord of this unit and turn the power off for all other system components before connecting or disconnecting any components. I Connection to receiver · Connect the SKW-150X subwoofer to the SUBWOOFER PREOUT jack on your receiver. I Power cord · Make sure that all connections other than the power cord for the system have already been made. · Turning on the power for the system may cause a very brief current surge that might affect other devices such as a computer, if both products are on the same circuit. Connect those devices to another AC outlet. Adjustment I Output level · Adjust the SKW-150X output level properly for your listening room and connected speakers. · Note that you may possibly set the subwoofer at high output levels because super bass-range sound is not as audible as sound in other ranges. [. . . ] If a speaker system is used near them, discoloration or distortion of pictures will occur. To allow use with color television sets, etc. , the SKF-103F Front speakers and SKC-103C Center speaker are provided with magnetic shielding. Even so, discoloration may still occur, depending on the installation environment. If discoloration occurs, turn off the television set, wait 15 to 30 minutes, and then turn it on again. [. . . ]