User manual ONKYO HTP-L50

[. . . ] English Contents Home Theater Speaker System Important Safeguards. . . . . . . . . . . . . . . . . . . . . . . . 2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Supplied Accessories. . . . . . . . . . . . . . . . . . . . . . . . 3 Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Power For European model Declaration of Conformity We, ONKYO EUROPE ELECTRONICS GmbH LIEGNITZERSTRASSE 6, 82194 GROEBENZELL, GERMANY declare in own responsibility, that the ONKYO product described in this instruction manual is in compliance with the corresponding technical standards such as EN60065, EN55013, EN55020 and EN61000-3-2, -3-3. MORI ONKYO EUROPE ELECTRONICS GmbH WARNING BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY. The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e. g. , AC 230 V, 50 Hz or AC 120 V, 60 Hz) written on the rear panel. For British model Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. IMPORTANT The wires in the mains lead are coloured in accordance with the following code: Blue : Neutral Brown : Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. For Canadian model For models having a power cord with a polarized plug: CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. IMPORTANT A 5 ampere fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 5 amperes and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMPERE SOCKET. If in any doubt, please consult a qualified electrician. Modèle pour les Canadien Sur les modèles dont la fiche est polarisée: ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. Supplied Accessories Make sure your box contains everything listed below. The number of accessories is indicated in brackets. · Subwoofer (SL-105) [1] · Satelite speakers (D-L1) [5] · Spacers for subwoofer [4] · Spacers for satelite speakers [20] · Speaker cable for L/R front and center speakers, 3. 5 m [3] · Speaker cable for surround speakers, 8 m [2] · Pin cord [1] (Red) (White) (Green) (Blue) (Gray) 3 Feature The HTP-L50 is a 5. 1-channel speaker package that consists of five satellite speakers and one subwoofer with an internal amplifier. The HTP-L50 features the SL-105 subwoofer with L/R mixing circuits and a built-in cut-off filter as the subwoofer and the D-L1 speakers with MDF (Medium Density Fiberboard) cabinet and OMF-cone as the five satellite speakers. Simply connect the speakers to your AV amplifier or receiver for superb surround audio playback. The speaker cables and satellite speaker terminals are colorcoded to facilitate connection. Connect each cable to the matching-colored terminal. Control positions and names Subwoofer SL-105 Front panel 2 POWERED SUBWOOFER 3 Rear panel SL-105 FREQUENCY OUTPUT LEVEL C SL-105 INPUT FROM AMP/RECEIVER SPEAKER LEVEL + R _ _ L + LINE INPUT AUTO STANDBY L (MONO) OFF ON OUTPUT TO SPEAKERS R + 50Hz 200Hz MIN MAX R _ _ L + D POWER AB 1 1 POWER switch and indicator A LINE INPUT jacks To AC outlet Pressing this button turns the power on (the indicator lights). Pressing the button again turns the power off (the indicator goes out). Red: Unit is in standby mode Green: Unit is in operation 2 FREQUENCY knob Connect these jacks to the LINE OUT jacks of the amplifier etc. B AUTO STANDBY switch Use this knob to select the high-frequency range at which you wish to cut off the signal to the subwoofer. You can select any frequency between 50 Hz and 200 Hz depending on the characteristics of the speaker system being used with the SL-105. 3 OUTPUT LEVEL knob This switch is used to turn on and off the auto standby function. (Two M5 screw holes, 60 mm pitch on the bottom and one M5 screw hole on the rear. ) Note: When attaching an accessory item to a speaker, be careful of the length of the screws used. Use only screws that provide the required strength with a screw length between 7 and 12 mm. M5 screw 5 mm 7 to 12 mm Surround speakers should be placed to the side of the listener or behind the listener. These speakers produce sound movements in all directions, create a sound environment that reflects the background, and create the sensation of being in the middle of the action. Subwoofer The subwoofer can be installed anywhere in the room, but in most situations you will obtain the best results by placing the subwoofer to the side near a corner of the room. [. . . ] Although it is not a sign of damage, decrease the speaker output level to prevent damage to the driver. Troubleshooting guide Subwoofer SL-105 Symptom Cause Remedy The unit does not turn on. No sound output · The power plug is not fully inserted. · The OUTPUT LEVEL knob is set to the MIN level. · Pin-connector cable(s) are disconnected at the LINE INPUT jacks. [. . . ]