User manual ONKYO HTX-22HD

[. . . ] Contents Digital Surround System Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 HTX-22HD Instruction Manual Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Turning On & First Time Setup . . . . . . . . . . . . . 30 Basic Operation Playing your AV components . . . . . . . . . . . . . . . . . . [. . . ] See "Audio Input Setup" on page 36. 1 Use HTX-22HD's [INPUT] button to select the TAPE input selector so that "TAPE" appears on the display. 2 Press and hold down the [INPUT] button (about 3 seconds) to change the setting. Repeat this step to select MD, CDR, or DOCK. From TAPE, the setting changes in the following order: 38 Playing Your Components Basic HTX-22HD Operation 3 1 3 1 1 HTX-22HD Press the HTX-22HD's [INPUT] button repeatedly to select an input source. To select an input source with the remote controller, use its [INPUT SELECTOR] buttons. Remote controller Depending on which input selectors you have assigned to input jacks (page 36), you can select the following input selectors: DVD, VCR/DVR, CBL/SAT, GAME/TV, TAPE, TUNER, CD. 2 Start playback on the source component. To watch a video source that's connected to an HDMI IN, on your TV, select the video input that's connected to the HTX-22HD's HDMI OUT. On some DVD players, you may need to change the digital or HDMI audio output settings. To adjust the volume, use the HTX-22HD's MASTER VOLUME control, or the remote controller's [VOLUME] buttons. 3 HTX-22HD Since the HTX-22HD is designed for home theaters, it has a wide volume range for precise adjustment. The volume can be adjusted from Min, 1 through 79, or Max. Remote controller You can limit the maximum volume with the MaxVolume setting (see page 67). 4 Select a listening mode and enjoy! See "Using the Listening Modes" on page 42. 39 Playing Your Components--Continued Using the Sleep Timer SLEEP DIMMER With the sleep timer, you can set the HTX22HD so that it turns off automatically after a specified period. Press the remote controller's [SLEEP] button repeatedly to select the required sleep time. MUTING Setting the Display Brightness You can adjust the brightness of the display. Press the remote controller's [DIMMER] button repeatedly to select dim, dimmer, or normal brightness. The sleep time can be set from 90 to 10 minutes in 10 minute steps. When the sleep timer has been set, the SLEEP indicator appears on the display, as shown. The selected sleep time appears on the display for about 5 seconds, then the previous display appears. SLEEP indicator Muting the HTX-22HD You can temporarily mute the output of the HTX-22HD. Press the remote controller's [MUTING] button. To cancel the sleep timer, press the [SLEEP] button repeatedly until the SLEEP indicator disappears. To check the remaining sleep time, press the [SLEEP] button. Note that if you press the [SLEEP] button while the sleep time is being displayed, you'll shorten the sleep time by 10 minutes. The output is muted and the MUTING indicator flashes on the display. To unmute the HTX-22HD, press the remote controller's [MUTING] button again, or adjust the volume. The output is unmuted and the MUTING indicator goes off. Muting is cancelled when the HTX-22HD is set to Standby. 40 Playing Your Components--Continued DISPLAY Displaying Source Information You can display various information about the current input source as follows. Press the remote controller's [DISPLAY] button repeatedly to cycle through the available information. The following information can typically be displayed: Input source & volume Signal format*1 or sampling frequency Input source & listening mode *1 If the input signal is analog, no format information is displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about 3 seconds, then the previous display reappears. 41 Using the Listening Modes Selecting the Listening Modes For a description of each listening mode, see "About the Listening Modes" on page 49. · The Dolby Digital and DTS listening modes can only be selected if your DVD player is connected to the HTX-22HD with a digital audio connection (coaxial, optical, or HDMI). · The listening modes that you can select depends on the format of the input signal. To check the format, see "Displaying Source Information" on page 41. Remote controller To select the listening modes, repeatedly press the [LISTENING MODE] buttons on the HTX-22HD or remote controller. HTX-22HD The name of the selected listening mode is shown on the display. LISTENING MODE LISTENING MODE 42 Using the Listening Modes--Continued Listening Modes Available for Each Source Format Analog and PCM Sources PCM Source format 32­96 kHz*1 176. 4/ 192 kHz*2 Multi channel Analog Multichannel PCM 32­96 kHz*1 176. 4/192 kHz*2 MultiMono/ MultiMono/ 2ch 2ch channel Multiplex channel Multiplex DVD, Blu-ray disc DVD, Blu-ray disc Media CD, TV, radio Listening Mode Direct Stereo Mono Multichannel Dolby PLII Movie/ Dolby PLIIx Movie*3 Dolby PLII Music/ Dolby PLIIx Music*3 Dolby PLII Game/ Dolby PLIIx Game*3 DolbyEX Neo:6 Neo:6 Cinema Neo:6 Music MonoMovie*5 *6 Orchestra*5 *6 Unplugged*5 *6 Studio-Mix*5 *6 TV Logic*5 *6 AllChStereo FullMono T-D *6 Surround Sensation*7 1. DVD *4 *4 *4 *4 32/44. 1/48/88. 2/96 kHz Multichannel 176. 4/192 kHz PCM is output only via HDMI. If there are no surround back speakers, Dolby Pro Logic II is used. Available only when using surround speakers. PCM at 88. 2 kHz and 96 kHz is processed at 44. 1 kHz and 48 kHz respectively. Cannot be selected with some source formats. Surround Sensation does not support 32 kHz input signals. [. . . ] · Check the Speaker Configuration (page 56). There's no sound with a certain signal format · Check the digital audio output setting on the source component. On some game consoles, such as those that can play DVDs, the default setting is off. · With some DVD-Video discs, you need to select an audio format from a menu or with the AUDIO button on your DVD player's remote controller. The volume cannot be set to 79 (99) on. This is to prevent noise when you use the pause, fast forward, or fast reverse function on your player. [. . . ]