User manual ONKYO ND-S1 REMOTE CONTROL CODES

[. . . ] 2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Digital Media Transport ND-S1 Instruction Manual Supplied Accessories. . . . . . . . . . . . . . . . 8 Playing the Music and Videos on Your iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Syncing Your iPod to Your PC. . [. . . ] 2 OPTICAL AUDIO OUT jack This optical digital audio output jack connects to an optical digital audio input on a system component, amp, or AV receiver. 3 COAXIAL AUDIO OUT jack This coaxial digital audio output jack connects to a coaxial digital audio input on a system component, amp, or AV receiver. 4 USB port Connects to a USB port on your PC for playing music stored on your PC and iTunes sync. 5 VIDEO OUT jack Connects to a composite video input on your TV or AV receiver for video playback. 6 DC IN 5V 1A jack Connect the included AC adapter here. 1 6 Using the Remote Controller Aiming the Remote Controller RC Replacing the Battery The included remote controller uses a CR2025 type battery. Refer to the Digital Input Setup and Changing the Display sections of your amp or AV receiver's instruction manual for details. PC TV 1. Using the included optical audio cable, connect the ND-S1's OPTICAL AUDIO OUT jack to an optical digital audio input jack on your amp or AV receiver. If your iPod supports TV out, use the included video cable to connect the ND-S1's VIDEO OUT jack to a composite video input on your TV or AV receiver. Using the included cable, connect the ND-S1's REMOTE CONTROL jack to an jack on your amp or AV receiver. Connect the included AC adapter to the ND-S1's DC IN 5V 1A jack, and plug the AC adapter into a suitable wall outlet. VIDEO INPUT USB cable ND-S1 Video cable Optical digital audio cable To wall outlet AC adapter Notes: · The ND-S1's audio outputs are digital outputs. If the digital audio input on your amp or AV receiver cannot be assigned to an input selector whose Input Display can be set to "DOCK, " do not connect the cable, otherwise a malfunction may occur. · Do not place the ND-S1 on top of a component that gets warm or one with has air vents on top, as it may interfere with that component's cooling or cause the component or ND-S1 to overheat. Place it next to the component, use an audio rack, etc. cable AV receiver 8 Inserting Your iPod into the ND-S1 Prepare the adapter that came with your iPod. Gently push down and slide open the dock cover on the ND-S1. iP od P C U SY NN SC Y/ N C ON AN /ST Y DB STAN DB Y od iP TR AN SP T OR 2. Insert the adapter supplied with your iPod, then push your iPod firmly onto the ND-S1's dock connector. Notes: · If the [iPod] indicator does not light up after you've inserted your iPod, this means that your iPod is not properly seated on the dock connector. Make sure your iPod is seated properly on the dock connector. · To prevent dock connector damage, don't twist your iPod when inserting or removing it, and be careful not to knock your iPod while it's inserted. · Don't use your iPod with any other accessories, such as FM transmitters and microphones, because they may cause a malfunction. Removing the iPod Adapter To remove the iPod adapter from the ND-S1, insert a small flathead screwdriver into the slot, and lift it out, as shown below. Adapter supplied with iPod iP od PC UN SY SY NC NC / Y NDB STA ON/ Y NDB STA iPo d TR AN SP T OR Notes: · If you use a case with your iPod, always remove it before you insert it. Otherwise, it may not connect properly and a malfunction may occur. · Do not insert your iPod into the ND-S1 without the adapter that came with it, as it may put unnecessary strain on the iPod or ND-S1's dock connector, causing permanent damage. When you insert your iPod, the ND-S1 works as follows depending on the status of your iPod. [. . . ] · Make sure all plugs are pushed in all the way. · Make sure the ND-S1 is connected to the correct input jacks on your amp or AV receiver. If there's no video, check your video connections. Do not connect the ND-S1 to any jacks on your amp or AV receiver labeled OUT. [. . . ]