User manual ONKYO P-3000R

[. . . ] Preamplifier P-3000R Instruction Manual En Introduction WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Install in accordance with the manufacturer's instructions. [. . . ] The preamplifier supports high-speed USB 2. 0. The maximum sampling rate for PCM input is 192 kHz/32 bit, 2ch. Optical digital connections allow you to enjoy digital sound such as PCM. The maximum sampling rate for PCM input is 96 kHz/24 bit, 2ch. Coaxial digital connections allow you to enjoy digital sound such as PCM. The maximum sampling rate for PCM input is 192 kHz/24 bit, 2ch. Orange Analog audio (RCA) L USB digital audio USB Optical digital audio OPTICAL Coaxial digital audio White Red Analog audio connections (RCA) carry analog audio. R To use Mono mini-plug (Remote Interactive), you must make an audio connection between the preamplifier and the Onkyo Dock. Use the supplied or commercially available mono mini-plug cable to connect to the 12V trigger terminals on the other device for linked operation. The tip polarity of the connectors are as shown in the right. 12 volts positive tip polarity Note · · · · · Push plugs in all the way to make good connections (loose connections can cause noise or malfunctions). To prevent interference, keep audio cables away from power cords and speaker cables. The preamplifier's optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when it's removed. To prevent shutter damage, hold the optical plug straight when inserting and removing. The analog audio cable can be used instead of the coaxial cable. Right! Wrong! About Balanced Input (AES/EBU Jack) Plugging the AES/EBU cable Match the pins and insert the terminal until you hear a "click. " Make sure that the terminal is locked by lightly pulling the connection cable. Unplugging the AES/EBU cable Pull out the connection cable while holding down the lever. 1 Push 2 Push En 15 Connecting the Power Cord Preamplifier P-3000R AC INLET Supplied power cord To an AC wall outlet (Plug type varies from country to country. ) 1 2 3 4 Make sure that the main power of the preamplifier is turned off. Connect the supplied power cord to the preamplifier's AC INLET. Plug the power cord into an AC wall outlet. Tip · To reduce noise, do not tie the signal cable and power cable together. Wire them so that they are away from each other. Note · Never disconnect the power cord from the preamplifier while the other end is still plugged into a wall outlet. Always disconnect the power cord from the wall outlet first, and then the preamplifier. · Turning on the preamplifier may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the preamplifier into a different branch circuit. · Do not use a power cord other than the one supplied with the preamplifier. The supplied power cord is designed exclusively for use with the preamplifier and should not be used with any other equipment. En 16 Connecting a Compact Disc Player Analog Connection Preamplifier P-3000R Preamplifier P-3000R Digital (Optical or Coaxial) Connection L R Compact Disc Player C-7000R Compact Disc Player C-7000R Connect either of them. En 17 Digital AES/EBU Connection Connecting the Onkyo Dock Preamplifier P-3000R Preamplifier P-3000R Connect either of them. COAXIAL OPTICAL Compact Disc Player C-7000R ON /ST AN DB Y ST AN DB Y iP o d PC UN SYN SY C/ NC Digital Media Transport Note · You need to change the selector name to use · Use only cables for connections. [. . . ] · If you have any devices that emit high-intensity radio waves near the preamplifier, such as a cellular phone that's being used to make a call, the preamplifier may output noise. The Preamplifier turns off unexpectedly. · When the set ASb starts running, the preamplifier will automatically go Standby ( 35). En 36 PC Playback Can't playing the music files on the PC. · Make sure that the USB cable is plugged in firmly ( 15). · Make sure that the USB driver is installed successfully ( 31). Onkyo Dock There's no sound. · Make sure that the Onkyo Dock is connected to the preamplifier properly. · Make sure that no video content is being played. · Reset the iPod. Remote Controller The remote controller doesn't work properly. · Make sure the batteries have been installed with the correct polarity (+/­) ( 10). [. . . ]