User manual ONKYO P-388F

[. . . ] Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. [. . . ] button Used to fast reverse the current song. button Used to fast forward the current song. Controlling the Onkyo Dock ( 32) Dock control buttons SHUFFLE button Used with the shuffle function. MENU button Opens iPod menu or returns to the previous menu. REPEAT button Used with the repeat function. button Used to select the previous song. / button Used to start or pause playback. button Used to select the next song. You can also use the remote controller to control your Onkyo compact disc player (such as C-7000R) and Onkyo Dock. Note · Depending on the component, you may not be able to control with the remote controller. Controlling the Onkyo Compact Disc Player ( 30) CD button Used to turn on the Onkyo compact disc player and select the CD input selector directly. En 14 Connections Connections Cable and Jacks Balanced AES/EBU This is a professional digital audio interface. Balanced AES/EBU cables are used for better noise immunity and longer cable runs. The maximum sampling rate for PCM input is 192 kHz/24 bit, 2ch. The supplied power cord is designed exclusively for use with the preamplifier and should not be used with any other equipment. En 16 Connecting a Compact Disc Player Analog Connection Preamplifier P-388F Preamplifier P-388F Digital (Optical or Coaxial) Connection L R Compact Disc Player C-7000R Compact Disc Player C-7000R Connect either of them. En 17 Digital AES/EBU Connection Connecting the Onkyo Dock Preamplifier P-388F Preamplifier P-388F Connect either of them. COAXIAL OPTICAL Compact Disc Player C-7000R ON /ST AN DB Y ST AN DB Y iP o d PC UN SYN SY C/ NC Digital Media Transport Note · You need to change the selector name to use · Use only cables for connections. cables are supplied with Onkyo Docks. · Connect only Onkyo Dock to jacks. Connecting other manufacturer's components may cause a malfunction. · Use only the Onkyo Dock with digital connections. This is an example of the connection using the compact disc player C-7000R. En 18 Connecting a Turntable Preamplifier P-388F Connecting a Cassette Tape Deck Preamplifier P-388F L L R R L R AUDIO OUTPUT L AUDIO OUT R Turntable (MM) without a built-in phono preamp Cassette tape deck Remove the short pins plugged into the jacks before connecting a turntable to the PHONO inputs. Tip · If your turntable (MM) has a phono built-in preamp, you can connect to other analog inputs such as CD IN or LINE 1 IN. · If your turntable has a moving coil (MC) type cartridge, you'll need a commercially available MC head amp or MC transformer to connect to PHONO IN. See your turntable's manual for details. · If your turntable has a ground wire, connect it to GND screw. With some turntables, connecting the ground wire may produce an audible hum. If this happens, disconnect it. Connecting a Recording Component Preamplifier P-388F L R L AUDIO IN R Cassette tape deck Note · Set "LINEOUT" setting to "RECOUT" ( 34). · When connecting a player recorder to TAPE IN (LINE 3 IN) and TAPE OUT (LINE OUT), always change the "LINEOUT" setting to the "RECOUT" ( 34). En 19 Connecting a Power Amplifier Stereo Connection Preamplifier P-388F Power Amplifier M-5000R Right speaker Left speaker This is an example of the stereo connection using the power amplifier M-5000R. En 20 Bi-amping Connection Preamplifier P-388F Power Amplifier M-5000R Tweeter (high) Woofer (low) Power Amplifier M-5000R Tweeter (high) Woofer (low) Right speaker Left speaker This is an example of the bi-amping connection using the power amplifier M-5000R. [. . . ] So don't do it. Power Can't turn on the Preamplifier. · Make sure that the power cord is properly plugged into the wall outlet ( 16). · Unplug the power cord from the wall outlet, wait 5 seconds or more, then plug it in again. The volume adjustment of LINE 2 does not work · Lower the volume of the connected AV receiver, and release "THROUGH" of "L2 OUT" of the preamplifier ( 35). The sound quality is not good. · Make sure all audio connecting plugs are pushed in all the way ( 15). · The sound quality can be affected by strong magnetic fields, such as that from a TV. Try moving any such devices away from the preamplifier. [. . . ]