User manual ONKYO PTS-303

[. . . ] 36 Using the Tuner. . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Enjoying the Listening Modes . . . . . 46 Thank you for purchasing an Onkyo 5. 1ch Home Theater System. Please read this manual thoroughly before making connections and plugging in the unit. [. . . ] To turn off the test tone, press the [TEST TONE] button again. · If the test tone is not produced by a speaker, or it's produced by a speaker other than that shown on the display, you may have wired the speakers incorrectly and you should check your connections (see page 20). · If the test tone is not produced by a speaker and its name does not appear on the display, you may have set the speaker settings incorrectly (see page 52). 34 First Time Setup Assigning Digital Inputs to Input Sources Changing the Input Display If you connect an -capable Onkyo MiniDisc recorder, CD recorder, or next generation HDD-compatible component to the TAPE IN/OUT or VIDEO 3 IN jacks, for to work properly, you must change this setting. This setting can only be changed on the AV receiver. TUNING / PRESET 2, 3 TUNING / PRESET MASTER VOLUME STANDBY/ON ENTER STANDBY A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP CLEAR PHONES MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER CD MASTER VOLUME STANDBY/ON ENTER STANDBY A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP 1 To enjoy Dolby Digital and DTS, you must connect your DVD player to the AV receiver by using a digital audio connection (coaxial or optical). Here are the default assignments. Input selector DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE CD Default assignment COAX ---OPT 1 ------OPT 2 CLEAR PHONES MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER CD 1, 2 1, 2 iPod photo: If you're using an iPod photo with the DS-A1 Remote Interactive Dock, connect the DS-A1's S VIDEO jack directly to an S-Video input on your TV. 1 TAPE Press the [TAPE] or [VIDEO 3] input selector button so that "TAPE" or "VIDEO3" appears on the display. With this function, you can assign digital inputs to input sources. For example, if you connect your DVD player to DIGITAL IN OPTICAL, you'll need to assign that input (OPT1) to the DVD input source. You can change the assignments as follows. Note: Make sure you also set your digital sources to send out a digital signals. Please refer to the digital sources' manual. or VIDEO 3 2 TAPE 1 DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER CD 2 DIGITAL INPUT Press the [DIGITAL INPUT] button. The current assignment appears. Note: HDD can be selected for the TAPE input selector or VIDEO 3 input selector, but not both at the same time. 3 DIGITAL INPUT Press the [DIGITAL INPUT] button repeatedly to select COAX, OPT1, OPT2, or "­ ­ ­ ­" (analog). For the VIDEO 3 input selector, the setting changes in this order: VIDEO 3 HDD Press the input selector button for the source that you want to assign. (Digital inputs cannot be assigned to the TUNER input source. ) or VIDEO 3 Press and hold down the [TAPE] or [VIDEO 3] input selector button (about 3 seconds) to change the setting. You can store your favorite stations as presets for quick selection. 1 TUNER Use the [TUNER] input selector button to select either AM or FM. In this example, FM has been selected. Manual Tuning Mode 1 TUNING MODE Press the [TUNING MODE] button so that the AUTO indicator disappears from the display. Band Frequency (Actual display depends on country. ) 2 TUNING / PRESET ENTER AM Frequency Step Setup (not North America and Europe) Here you can specify the AM frequency step used in your area. When this setting is changed, all radio presets are deleted. Press and hold the TUNING Up or Down [ ]/[ ] button. The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time. 1 2 Press the [SETUP] button to display "0. Hardware Setup, " and then press [ENTER]. Use the Up and Down [ ]/[ ] buttons to select "AM Freq, " and then use the Left and Right [ ]/[ ] buttons to select: 10 kHz: Select if 10 kHz steps are used in your area. 9 kHz: Select if 9 kHz steps are used in your area. Setup closes. The American model changes FM frequency in 0. 2 MHz steps, 10 kHz steps for AM. For other models it's 0. 05 MHz steps for FM and 9 kHz or 10 kHz steps for AM. When tuned into a station, the TUNED indicator appears. [. . . ] · Make sure that the batteries are installed with the correct polarity (page 7). · Make sure that the remote controller is not too far away from the AV receiver, and that there's no obstruction between the remote controller and the AV receiver's remote control sensor (page 7). · Make sure you've selected the correct remote controller mode (page 12). · Make sure you've entered the correct remote control code. [. . . ]