User manual ONKYO R-801A

[. . . ] English TUNER AMPLIFIER Before using R-801A Connections Instruction Manual TUNER AMPLIFIER VOLUME Preparations Operation STANDBY STANDBY / ON DISPLAY MEMORY FM MODE INPUT TUNING PHONES CLEAR ACOUSTIC PRESENCE R- 8 01A European models front panel shown. Other Information Thank you for purchasing the ONKYO R-801A Tuner Amplifier. Please read this manual thoroughly before making any connection or turning on the power. Follow these instructions to obtain optimum performance and maximum listening enjoyment from your new R-801A. Please retain this manual for future reference. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] It is strongly recommended that you install an outdoor FM antenna since the FM indoor antenna may not receive RDS broadcasts well enough to allow ACCUCLOCK to function properly. · The clock will display the time in a 24 hour cycle. For example, 5:30 pm will be displayed as "17:30". (You can select a 12 hour cycle display setting. For more information, see page 25. ) · If RDS signals cannot be received, no RDS station will be found. If an RDS signal is present but the signal is not strong enough, the ACCUCLOCK cannot set the time automatically, and the indication on the display turns off. (See page 24. ) Disappear Setting the clock automatically (European models only) ACCUCLOCK starts operating as soon as the power cord is plugged in. It then searches for an RDS broadcasting station which regularly sends time signals and waits to receive such time information. Do not operate any buttons until the clock setting is complete. The R-801A retains the clock setting until you unplug the power cord. The following steps describe how to set the clock automatically: 1. "AUTO" flashes slowly on the display. flashes slowly 2. Once an RDS station that sends time signals is detected, the indicator flashes more rapidly. Adjust the clock manually. flashes rapidly 3. Once the time signal is received from the RDS station, "CLOCK ADJUSTED" will scroll on the display. The received time information (the day of the week and the time) appears. 5. The time indicator turns off. Disappear · You may wish to adjust the clock manually because the time information may differ depending on the RDS station detected. If so, follow the manual clock adjustment procedure described on page 24. · There may be cases in which you can listen to radio broadcasts but cannot use the ACCUCLOCK function. · Once activated, ACCUCLOCK will remember the RDS station it uses for two weeks even if the power cord of this unit is unplugged. If you move outside the service area of the memorized RDS station and find out that ACCUCLOCK is not functioning, see "Confirming/changing the RDS Station used by ACCUCLOCK" on page 23 to change the memorized RDS station. 22 STANDBY/ ON ACOUSTIC PRESENCE CDR/PC TAPE INPUT SELECTOR CD/ DVD MD FM AM VOLUME TAPE REW UP TAPE FF MUTING DOWN SLEEP CLOCK TIMER ENTER TIMER MODE TAPE REPEAT CD/DVD CLEAR MD , ENTER SCROLL CDR/PC 1 5 9 2 6 10/0 3 7 --/--- 4 8 Confirming/changing the RDS station used by ACCUCLOCK If you wish to know which RDS station has been used to set the clock by ACCUCLOCK, or to use a different RDS station signal to set the clock, follow the steps below: 2 If "AUTO" appears on the display, press the ENTER button. If "MANUAL" appears on the display, press the button to select "AUTO, " then or press the ENTER button. ENTER 1 Press TIMER the TIMER button repeatedly until "ADJUST" is selected on the display, then press the ENTER button. MHz ENTER "AUTO" or "MANUAL" appears on the display. The example shown above indicates that the ACCUCLOCK function uses the RDS station whose information appears on the display (FM 88. 10 MHz). If the frequency of the RDS station has not been specified, "--:--" appears instead of the frequency of the station. [. . . ] · Move the antenna as far away as possible from the fluorescent lamp. · Install an outdoor FM antenna as far away as possible from the road. · Noise caused by turning a fluorescent lamp on and off. · Noise from automobile ignition. · Change to FM indoor antenna. Tuning indicators · Station is too strong. [. . . ]