User manual ONKYO SKC-750C

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5. 1ch Home Theater System HT-SP904 AV Receiver (HT-R557) Front Speakers (SKF-750F) Center Speaker (SKC-750C) Surround Speakers (SKM-750S) Powered Subwoofer (SKW-750) Remote Interactive Dock (DS-A1X) Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Turning On & First Time Setup. . . . . 36 Instruction Manual Basic Operation Playing your AV components . . . . . . . [. . . ] If you connect a video component to HDMI IN 1 or 2, you must assign that input to an input selector. For example, if you connect your DVD player to HDMI IN 1, you must assign HDMI DVD setting to IN1. IN1: Select if the video component is connected to HDMI IN 1. IN2: Select if the video component is connected to HDMI IN 2. No: Select if you're not using the HDMI OUT. HDMI video Input 4 SETUP Press the [SETUP] button. Setup closes. 40 First Time Setup--Continued Digital Audio Input Setup Changing the Input Display If you connect an -capable Onkyo MiniDisc recorder, CD recorder, or RI Dock to the TAPE IN/OUT or CBL/SAT IN jacks, for to work properly, you must change this setting. This setting can only be changed on the AV receiver. 2, 3 STANDBY/ON STANDBY 1 MASTER VOLUME TUNING PRESET MULTI CH DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP ENTER RETURN AUX INPUT PHONES SETUP MIC VIDEO L AUDIO R DISPLAY DIGITAL INPUT TONE STEREO LISTENING MODE DIMMER MEMORY TUNING MODE CLEAR 1, 2 STANDBY/ON 1, 2 MASTER VOLUME TUNING PRESET To enjoy Dolby Digital and DTS, you must connect your DVD player to the AV receiver digitally (coaxial or optical). These are the default digital audio input assignments. Input selector DVD VCR/DVR CBL/SAT TAPE CD AUX Default assignment COAX 1 OPT 1 COAX 2 ---OPT 2 ---- STANDBY MULTI CH DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP ENTER RETURN AUX INPUT PHONES SETUP MIC VIDEO L AUDIO R DISPLAY DIGITAL INPUT TONE STEREO LISTENING MODE DIMMER MEMORY TUNING MODE CLEAR 1 TAPE Press the [TAPE] or [CBL/SAT] input selector button so that "TAPE" or "CBL/SAT" appears on the display. or You can change the digital audio input assignments if necessary. For example, if you connect your DVD player to the OPTICAL 1 DIGITAL IN (OPT1), you must assign that input to the DVD input selector, as follows. CBL/SAT 1 DVD VCR/DVR CBL/SAT AUX TAPE Press the input selector button for the input selector that you want to assign. (Digital inputs cannot be assigned to the TUNER input selector. ) 2 TAPE or CD CBL/SAT Press and hold down the [TAPE] or [CBL/SAT] input selector button (about 2 seconds) to change the setting. Repeat this step to select MD, CDR, or DOCK. For the TAPE input selector, the setting changes in this order: TAPE MD CDR DOCK For the CBL/SAT input selector, the setting changes in this order: CBL/SAT DOCK 2 DIGITAL INPUT Press the [DIGITAL INPUT] button. The current assignment appears. 3 DIGITAL INPUT Press the [DIGITAL INPUT] button repeatedly to select COAX1, COAX2, OPT1, OPT2, or "­ ­ ­ ­" (analog). Note: DOCK can be selected for the TAPE input selector or CBL/SAT input selector, but not both at the same time. Note: Make sure that components connected digitally are configured to output digital audio. Refer to the relevant manuals. 41 Playing Your AV Components Basic AV Receiver Operation MULTI CH 1 TUNING PRESET 4 MASTER VOLUME STANDBY/ON REMOTE MODE RECEIVER TAPE/AMP DVD M D/CDR 1 Subwoofer's rear panel 1 INPUT SELECTOR 1 VCR/DVR 2 CBL/SAT 3 6 DVD CD DOCK STANDBY/ON 4 AUX 5 MULTI CH TV STANDBY 7 TAPE 8 TUNER 9 CD VCR 12 CABLE 10 MULTI CH DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP ENTER RETURN 11 +10 D TUN AUX INPUT 0 ENT DIMMER CLR SLEEP SAT --/--R PHONES SETUP MIC VIDEO L AUDIO 4 4 MIN MAX DISPLAY DIGITAL INPUT TONE STEREO LISTENING MODE DIMMER MEMORY TUNING MODE CLEAR TV INPUT GUIDE TOP MENU VOL DISC ALBUM CH VOL DISPLAY 2 PREVIOUS MENU OUTPUT LEVEL SP A / B MUTING ENTER PLAYLIST/CAT PLAYLIST/CAT SETUP RETURN 1 AV receiver Remote controller RECEIVER DVD VCR/DVR CBL/SAT Use the AV receiver's input selector buttons to select the input source. To select the input source with the remote controller, press the [RECEIVER] REMOTE MODE button, and then use the INPUT SELECTOR buttons. AUX TAPE TUNER CD 1 VCR/DVR 2 CBL/SAT 4 AUX 6 DVD 7 TAPE 8 TUNER 9 CD 2 Start playback on the source component. To watch a DVD or other video source, on your TV, select the video input that's connected to the AV receiver's MONITOR OUT jack. If your TV is connected to the HDMI OUT, see the tip on page 28. To adjust the volume, use the MASTER VOLUME control, or the remote controller's [VOL] button. The volume can be set to MIN, 1 through 79, or MAX. Since the AV receiver is designed for home theater enjoyment, it has a wide volume range for precise adjustment. To set the level of the subwoofer, use the OUTPUT LEVEL control. Because our ears are less sensitive to very low bass sounds, there's a temptation to set the level of the subwoofer too high. [. . . ] There's no video · Make sure that your iPod's TV OUT setting is set to On. Others The sound changes when I connect my headphones · When a pair of headphones is connected, the listening mode is set to Stereo, unless it's already set to Stereo, Mono, Direct. How do I change the language of a multiplex source · Use the "Multiplex" setting on the "Audio Adjust" menu to select Main or Sub (page 55). 68 Troubleshooting--Continued The functions don't work · To use , you must make an connection and an analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally (page 35). During automatic speaker setup, measurement fails and the message "Noise Error!" appears · This can be caused by a speaker malfunction. Make sure all of your speakers are working properly. The AV receiver contains a microcomputer for signal processing and control functions. [. . . ]