User manual ONKYO SKC-940C

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 7. 1ch THX Certified Digital Surround Receiver and Speaker Package Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 HT-S990THX AV Receiver (HT-R940) Front Speakers (SKF-940F) Center Speaker (SKC-940C) Surround Speakers (SKM-940S) Surround Back Speakers (SKB-940) Powered Subwoofer (SKW-940) Turning On & First Time Setup. . . . . 34 Basic Operation Playing your AV components . . . . . . . [. . . ] *2 If the input signal is analog, or AM or FM radio is selected, no format information is displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about 3 seconds, then the previous display reappears. Note: · The listening mode is displayed only when speaker set A is on. Interpreting Surround Channel Information Press the [RECEIVER] REMOTE MODE button, followed by the [MULTI CH] button. The MULTI CH indicator appears on the display. MULTI CH indicator MULTI CH A BC Audio from the multichannel DVD input will now be used for the DVD input source. Note: · While the multichannel DVD input is selected, the Speaker Configuration settings on page 55 are ignored, and signals from the multichannel input are fed to the speakers as they are. A: The number of front channels (front left, front right, and center). B: The number of surround channels (surround left and surround right). If there's surround back channel information, this number will be 3. C: LFE channel for subwoofer (1 means yes). 38 Listening to the Radio Listening to AM/FM stations TUNER TUNING MASTER VOLUME TUNING PRESET Manual Tuning Mode 1 TUNING MODE Press the [TUNING MODE] button so that the AUTO indicator disappears from the display. STANDBY/ON STANDBY ENTER MULTI CH DVD VIDEO 1 VIDEO 2 VIDEO 3 TAPE TUNER CD RETURN SETUP 2 TUNING PRESET VIDEO 3 INPUT VIDEO L AUDIO R VCR PHONES SPEAKERS A B TONE THX LISTENING MODE DISPLAY DIGITAL INPUT DIMMER MEMORY TUNING MODE CLEAR TUNING MODE Press and hold the TUNING Up or Down [ ]/[ ] button. The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time. With the built-in tuner, you can enjoy AM and FM radio stations. 1 TUNER Use the [TUNER] input selector button to select AM or FM. In this example, FM has been selected. The American model changes FM frequency in 0. 2 MHz steps, 10 kHz steps for AM. For other models it's 0. 05 MHz steps for FM and 9 kHz (or 10 kHz) steps for AM. When tuned into a station, the TUNED indicator appears. When tuned into a stereo FM station, the FM STEREO indicator also appears. TUNED AUTO Band Frequency (Actual display depends on country. ) FM STEREO Tuning into AM/FM Radio Stations Auto Tuning Mode Tuning into Weak FM Stereo Stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono. Note: · You can also use the remote controller's Up and Down [ ]/[ ] buttons to tune the radio. 1 TUNING MODE Press the [TUNING MODE] button so that the AUTO indicator appears on the display. 2 TUNING PRESET Press the TUNING Up or Down [ ]/[ ] button. Searching stops when a station is found. 39 Listening to the Radio--Continued Tuning into Stations by Frequency You can tune into AM and FM stations directly by entering the appropriate frequency. ON/STANDBY REMOTE MODE 2 MEMORY Press the [MEMORY] button. The MEMORY indicator appears and the preset number flashes. RECEIVER TAPE DVD M D/CDR RECEIVER INPUT SELECTOR Number buttons D TUN 1 V1 2 V2 3 V3 CD HDD 4 7 TAPE 5 MULTI CH 6 DVD TV 3 CH +/­ TUNING PRESET 8 TUNER 9 CD VCR 12 CABLE 10 11 +10 D TUN 0 ENT DIMMER CLR SLEEP SAT --/--- While the MEMORY indicator is displayed (about 8 seconds), use the PRESET [ ]/[ ] buttons to select a preset from 1 through 40. ENTER TV INPUT GUIDE TOP MENU VOL DISC ALBUM CH VOL PREVIOUS MENU SP A / B MUTING ENTER PLAYLIST/CAT PLAYLIST/CAT 4 MEMORY RETURN SETUP 1 RECEIVER Press the [RECEIVER] button, followed by the [D TUN] button. Press the [MEMORY] button again to store the station. The station is stored and the preset number stops flashing. [. . . ] Be sure to enter the appropriate remote control code first (see page 57). 62 Troubleshooting--Continued The AV receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this happens, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in again. Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit's malfunction. [. . . ]