User manual ONKYO SKF-330F

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5. 1ch Home Theater System HT-S580 AV Receiver (HT-R330) Front Speakers (SKF-330F L/R) Center Speaker (SKC-330C) Surround Speakers (SKM-330S L/R) Subwoofer (SKW-330) Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Turning On & First Time Setup. . . . . 32 Instruction Manual Basic Operation Playing your AV components . . . . . . . [. . . ] Setup closes. TESTING THE SPEAKERS To test that all of the speakers are working properly, press the remote controller's [TEST TONE] button. The test tone will be output by each speaker in turn and the name of each speaker will appear on the display. To turn off the test tone, press the [TEST TONE] button again. · If the test tone is not produced by a speaker, or it's produced by a speaker other than that shown on the display, you may have wired the speakers incorrectly and you should check your connections (see page 18). · If the test tone is not produced by a speaker and its name does not appear on the display, you may have set the speaker settings incorrectly (see page 34). 35 Playing Your AV Components Basic AV Receiver Operation 2 STANDBY/ON DISPLAY TUNING / PRESET 4 1 MASTER VOLUME ENTER ON STANDBY REMOTE MODE RECEIVER TAPE/AMP DVD 1 INPUT SELECTOR 1 V1 2 V2 3 V3 CD 4 7 TAPE TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP 5 MULTI CH 6 DVD MD STANDBY 8 TUNER 9 CD CDR A SPEAKERS B +10 --/--CD 0 DIMMER CLR SLEEP CLEAR PHONES MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER DISC CH VOL 4 MULTI CH 1 2 TOP MENU MENU SP A / B MUTING ENTER 1 AV receiver DVD VIDEO 1/VCR VIDEO 2 Remote controller Use the AV receiver's input selector buttons to select the input source. To select the input source with the remote controller, press the [RECEIVER] button, and then use the INPUT SELECTOR buttons. On the remote controller, the [V1], [V2], and [V3] buttons select the VIDEO 1/VCR, VIDEO 2, and VIDEO 3 input sources respectively. VIDEO 3 TAPE TUNER CD 2 AV receiver A SPEAKERS B Remote controller Use the SPEAKERS [A] and [B] buttons on the AV receiver or the [SP A/B] button on the remote controller to select the speaker set that you want to use. Pressing the remote controller's [SP A/B] button cycles through the following settings: Speaker Set A Speaker Set A&B Speaker Set B Off. The A and B speaker indicators show whether each speaker set is on or off. Indicators Note that when speaker set B is turned on, speaker set A is reduced to 2. 1-channel playback. When you select DVD or another video component, on your TV you'll need to select the video input that's connected to the AV receiver's MONITOR OUT. 3 4 AV receiver MASTER VOLUME Remote controller VOL To adjust the volume, use the MASTER VOLUME control, or the remote controller's [VOL] button. The volume can be set to MIN, 1 through 79, or MAX. The AV receiver is designed for home theater enjoyment and has a wide volume range for precise adjustment. 5 Select a suitable listening mode and enjoy!See page 44. 36 Playing Your AV Components--Continued Displaying Source Information ON STANDBY REMOTE MODE RECEIVER TAPE/AMP DVD RECEIVER INPUT SELECTOR You can display various information about the current input source as follows. Press the [RECEIVER] button, and then press the [DISPLAY] button repeatedly to cycle through the available information. 1 V1 2 V2 3 V3 CD MULTI CH 4 7 TAPE 5 MULTI CH 6 DVD MD 8 TUNER 9 CD CDR +10 --/--- 0 DIMMER CLR SLEEP DISC CH VOL LISTENING MODE STEREO SURROUND The following information can typically be displayed for input sources. LEVEL+ AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE LEVEL- Input source & volume Signal format* or sampling frequency Input source & listening mode DISPLAY DISPLAY OR-EQ L NIGHT CINE FLTR RC-606S Using the Multichannel Input The multichannel input is for connecting a component with individual 5. 1-channel analog audio output jacks, such as a DVD player or MPEG decoder. Press the [RECEIVER] button followed by the [MULTI CH] button so that MULTI CH indicator appears on the display. Audio from the multichannel input will now be used for the DVD input source. MULTI CH indicator *If the input signal is analog, no format information is displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about three seconds, then the previously displayed information reappears. Interpreting Surround Channel Information A BC A: The number of front channels (front left, front right, and center). B: The number of surround channels (surround left and surround right). [. . . ] · To control cassette tape deck, point the remote controller at the AV receiver. · To control Onkyo CD player or MD/CD recorder, point the remote controller at that component. The AV receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this happens, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in again. [. . . ]