User manual ONKYO SKFSKS-4600

[. . . ] Sound produced when fast-forwarding cassette tape deck 3. High-frequency sound generated by an oscillator, an electronic musical instruments, etc. Special test signals produced by audio checking CD, etc. Sound produced when connecting or disconnecting audio connection cables (Always turn off the amplifier's power before connecting or disconnecting cables. ) 7. [. . . ] Also, be sure to connect the Right and Left speakers with the amplifier's corresponding speaker terminals. · Pull lightly on the speaker cables to ensure that they are connected firmly. ­+ SKM-4600 Surround right speaker ­+ SKM-4600 Surround left speaker 27122965 ANTENNA COMPONENT VIDEO INPUT 2 INPUT 1 OUTPUT CAUTION: SPEAKER IMPEDANCE 6 OHMS MIN. /SPEAKER FM 75 AM Y A L FRONT SPEAKERS B L SURROUND SPEAKERS CENTER SPEAKER AC OUTLETS PB REMOTE CONTROL L R PR DIGITAL INPUT 2 OPTICAL 1 DIGITAL DIGITAL OUTPUT INPUT OPTICAL COAXIAL VIDEO 3 VIDEO 2 IN IN VIDEO 1 OUT IN DVD IN MONITOR OUT VIDEO R R SURROUND BACK SPEAKER S VIDEO AC 230-240 V 50 Hz SWITCHED TOTAL 100W MAX. CD IN TAPE OUT IN IN IN OUT IN FRONT SURR CENTER L SUBWOOFER PRE OUT L R L R R VIDEO 3 VIDEO 2 VIDEO 1 DVD SUB WOOFER AV Amplifier En-2 Placement SKF-4600 Front speaker system The sound quality a speaker system reproduces varies greatly depending on the construction and area of the room where it is installed, as well as the location and size of the furniture. For betterquality sound, observe the following precautions. · Avoid placing the speaker system on an elevated object such as on concrete blocks. Instead, place it on a rigid floor surface with minimal vibration. Also note that high-quality bass cannot be obtained if the speaker system is unstably positioned. Generally speaking, placing the speaker system on several small-diameter supports results in better bass than placing it directly on the installation surface. Moreover, if you feel the bass reproduced by the system is too weak, move the speaker system closer to the wall behind it. You can thus control the strength of the reproduced bass by the position of the speakers. · In many rooms, the furniture and wall affect the reproduced sound quality. For stereo sound reproduction, placing the Right and Left speakers in the same condition produces the best results. If they are placed in extremely different conditions, the Right- and Leftchannel balance will be adversely affected. · The ideal placement of the speaker system is as follows: Imagine an equilateral triangle and position the Right and Left speakers on both ends of the base. The ideal listening position is at or slightly to the rear of the triangle apex. · Glazed doors or surrounding walls in front of the speaker system may cause the resonance of specific frequency ranges due to reflected sound. To eliminate this resonance, place some sound-absorbing material such as a thick curtain in front of the doors or walls. Attaching the speaker stands (for SKF-4600 only) Attach the supplied speaker stand at the bottom of each speaker cabinet using the supplied screws as shown in the figure below. For better sound quality, you are recommended to attach the supplied cork spacer on the speaker stand. In addition to the sound quality improvement, attaching the cork spacers also provide non-sliding and stabilizing effects for the speaker cabinet. Screw M6 × 20 mm Speaker stand Speaker cabinet Cork spacer Attaching and detaching the speaker grilles This speaker system uses detachable grilles. Use the following method to attach or detach the grilles. While holding the bottom edge of the speaker grille with your both hands, pull it gently toward you to remove the bottom of the grille. [. . . ] Discoloration may also be caused when a magnet or other magnetizing object exists near the television because of the combined effect. SKM-4600 Surround Speaker If the speakers are to be wall-mounted, make sure that the walls are strong enough to support the speaker's weight. The weight that mounting screws can support varies greatly depending on the wall material and the position of the reinforcing ribs embedded in the wall. Use the thickest and longest possible mounting screws with mounting screw head diameters less than 10 mm and shank diameters less than 4 mm (consult with your interior designer or contractor). Speaker care Your Onkyo speakers are finished with a very high quality polymer laminate covering that serves to protect the wood speaker cabinet. Wipe the cabinet periodically with a dry, silicon-embedded or plain soft cloth. [. . . ]