User manual ONKYO SKS-HT230

[. . . ] Contents 5. 1 Ch Home Theater Speaker Package Getting Started Important Safeguards . . . . . . . . . . . . . . . . . . . . . 2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Following this, dry immediately with a clean cloth. Do not use rough material, thinners, alcohol or other chemical solvents or cloths since these may damage the finish or remove the panel lettering. Use a vacuum cleaner to remove dust from hard-to-reach grilles. Power WARNING BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY. The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e. g. , AC 230 V, 50 Hz) written on the rear panel. 3 Introduction The SKS-HT230's stylish enclosures are made of aluminum and their slim design makes them ideal for use with LCD and plasma TVs. SKS-HT230 The SKS-HT230 is a 5. 1-channel speaker package consisting of front left and right speakers, a center speaker, surround left and right speakers, and a powered subwoofer. Simply connect the speakers to your AV amp or receiver for superb surround sound playback. Speaker terminals and speaker cables are color-coded for easy identification. Simply connect each speaker cable to the same-colored speaker terminals. Package Contents Make sure your box contains all of the items below. If anything is missing, contact the nearest Onkyo dealer. · Front speakers (SKF-230F) · Speaker cable for front speakers (4. 5 m) · Spacers for wall mounting [×20] (Red) (White) · Cork spacers [×4] (For the subwoofer) · Front speaker bases · Front speaker base fixing screws [×8] · Center speaker (SKC-230C) · Speaker cable for center speaker (3 m) · Center speaker base (Green) · Surround speakers (SKM-230S) · Speaker cables for surround speakers (9 m) · Subwoofer (SKW-150X) · RCA cable for subwoofer connection (Blue) (Gray) SKW-150X POWERD SUBWOOFER The alphabet displayed at the end of the product name found in catalogs and on package represents the color of SKS-HT230. Though the color varies, the specifications and operations are the same. 4 Getting to know Your Speaker Package Subwoofer (SKW-150X) Front Front, Center & Surround Speakers (SKF-230F, SKC-230C, SKM-230S) 3 2 1 SKW-150X POWERD SUBWOOFER Rear 4 POWERED SUBWOOFER MODEL NO. SKW-150X OUTPUT LEVEL LINE INPUT MIN MAX 1 Speaker terminals POWER ON OFF RED : STANDBY GREEN : ON 2 3 1 To AC outlet These push terminals are for connecting the speaker to your DVD Receiver, amp, or other receiver with the supplied speaker cables. The supplied speaker cables are color-coded for easy identification. Simply connect each cable to the same-colored positive speaker terminal. 2 Keyhole slots These keyhole slots can be used to wall-mount the speaker either horizontally or vertically. A POWER switch and indicator To turn on the SKW-150X, set the POWER switch to the ON position (the indicator lights up). To turn off the SKW-150X, set the POWER switch to the OFF position (the indicator goes out). Red: The unit is in standby mode Green: The unit is in operation mode The SKW-150X automatically turns to Standby mode when no signal has been input for about 20 minutes. The SKW-150X automatically turns on when an input signal is detected in Standby mode. 3 Speaker mount/bracket inserts These threaded inserts can be used to attach the speaker either horizontally or vertically to a speaker mount or bracket. Note: Use commercially available M5 screws to attach the speaker to a speaker mount or bracket. 4 Base inserts (other than center speaker) These threaded inserts can be used to mount the speaker on the supplied base (screws included). B OUTPUT LEVEL control This control is used to adjust the output level of the subwoofer. C LINE INPUT The RCA input should be connected to the subwoofer preout on your AV receiver, amp, or other receiver with supplied RCA cable. Note: The Auto Standby function turns the subwoofer on when the input signal exceeds a certain level. If the Auto Standby function does not work reliably, try slightly increasing or decreasing the subwoofer output level on your receiver or amp. 5 Various Mounting Methods Front Speaker Bases If you intend to stand the front speakers on the floor or on a TV stand or AV stand, you should attach the supplied front speaker bases. With hollow walls, use a cable/pipe detector to check for any power cables or water pipes before making any holes. [. . . ] Or, the number of speaker channels is not set to 5ch. The power plug is not fully inserted into the wall outlet. The OUTPUT LEVEL control is set to minimum. The RCA cable is not properly connected to the subwoofer's LINE INPUT. [. . . ]