User manual ONKYO SKS-L500

[. . . ] 3 Speaker care. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 En Package Contents · · · · · SKC-L500C: Center speaker × 1 SKM-L500S: Surround speaker × 2 Speaker cable (green: 3 m, blue, gray: 9 m) Cork spacers, 12pcs. Bass for horizontal mounting × 1 The center speaker should be installed on the base securely. [. . . ] The cork spacers prevent the speakers from moving, providing a more stable setup. Cork spacers Bottom of the SKM-L500S Mounting horizontally To mount the speakers horizontally, use the two keyhole slots shown to hang each speaker on two screws that are securely screwed into the wall. Keyhole slot for wall mounting Center Speaker Base Use the center speaker base to mount the center speaker horizontally. If you place the speaker and its base on top of a TV or an entertainment center, adjust the angle of the speaker so that it faces toward the listening position. Cork spacers 2 The plaque of each speaker rotates so that you can position the speakers upside down. Caution: A mounting screw's ability to support a speaker depends on how well it's anchored to the wall. If you have hollow walls, screw each mounting screw into a stud. If there are no studs, or the walls are solid, use suitable wall anchors. Use screws with a head diameter of 9. 5 mm or less and a shank diameter of 4 mm or less. With hollow walls, use a cable/pipe detector to check for any power cables or water pipes before making any holes. Leave a gap of 5 mm Wall between the wall and the base of the screw head, as shown. (We recommend that you consult a home installation 5 mm professional. ) SKR-L500 Surround back speaker SKR-L500 Surround back speaker SKC-L500C Center speaker Green SKF-L500 Front right speaker SKF-L500 Front left speaker SURROUND BACK SPEAKERS SURROUND SPEAKERS FRONT SPEAKERS L Blue R Gray CENTER SPEAKER Connecting the Speakers Read the following before connecting your speakers: · Turn off your amp before making any connections. · The nominal impedance of these speakers is 6 . Use only an amp that supports this impedance. · Pay close attention to speaker wiring polarity. Connect positive (+) terminals to only positive (+) terminals, and negative (­) terminals to only negative (­) terminals. If the speakers are wired incorrectly, the sound will be out of phase and will sound unnatural. · Be careful not to short the positive and negative wires. Doing so may damage your amp. SKM-L500S Surround right speaker SKM-L500S Surround left speaker Using Speaker Mounts/Brackets Threaded inserts for 5 mm machine screws are provided for wall-mounting with commercially available speaker mounts and brackets (SKC-L500C: rear, SKM-L500S: rear and buttom). Refer to the manual supplied with your mounts or brackets for installation details. Note: Mount or bracket The portion of the screw that goes into the speaker's threaded insert should be 5 mm between 5 mm and 9 mm long. 5­9 mm Operating Precautions Connecting the Speaker Cables 1 2 Strip the insulation from the ends of the speaker cables, and twist the bare wires tightly. Use the cables to connect each speaker's input terminals to the corresponding speaker output terminals on your amp. To make a connection, while pressing the terminal lever, insert the wire into the hole, and then release the lever. Make sure that the terminals are gripping the bare wires, not the insulation. The speakers can handle the specified input power when used for normal music reproduction. If any of the following signals are fed to them, even if the input power is within the specified rating, excessive current may flow in the speaker coils, causing burning or wire breakage: 1. [. . . ] In some situations, however, discoloration may still be an issue, in which case you should turn off your TV or monitor, wait 15 to 30 minutes, and then turn it back on again. This normally activates the degaussing function, which neutralizes the magnetic field, thereby removing any discoloration effects. If discoloration problems persist, try moving the speakers away from your TV or monitor. Note that discoloration can also be caused by a magnet or demagnetizing tool that's too close to your TV or monitor. 2-way bass reflex 6 150 W 82 dB/W/m 60 Hz - 100 kHz 8 kHz 2. 8 L 8 cm A-OMF diaphragm × 2 2. 5 cm balanced dome Spring type color-coded 378 (W) × 161 (H) × 93 (D) mm (Overall dimensions) 1. 6 kg Magnetic shielding 2-way bass reflex 6 130 W 80 dB/W/m 60 Hz - 35 kHz 8 kHz 2. 1 L 8 cm cone 2. 5 cm balanced dome Spring type color-coded 161 (W) × 288 (H) × 93 (D) mm (Overall dimensions) 1. 1 kg Specifications and appearance are subject to change for improvement without prior notice. [. . . ]