User manual ONKYO T-4030

[. . . ] Contents DAB/FM Tuner Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . En-2 T-4030 Instruction Manual Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . En-14 Thank you for purchasing an Onkyo Tuner. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new Tuner. [. . . ] Coaxial digital connections allow you to enjoy digital sound such as PCM. The maximum sampling rate for PCM output is 48kHz/16bit, 2ch. Orange Coaxial digital audio Analog audio (RCA) White Red Analog audio connections (RCA) carry analog audio. R To use R (Remote Interactive), you need to connect your Onkyo AV components with an R cable. En-11 Connecting Your Components—Continued Connecting to an Amplifier Analog Connection T-4030 R Connection T-4030 Supplied R cable Supplied audio cable Amplifier Amplifier Use the supplied audio cable to connect the T-4030’s AUDIO OUTPUT L/R jacks to the LINE IN jacks on your amplifier, as shown. To use the R system functions, use the supplied R cable to make an R connection (see the next column). Note: • If the T-4030 is used with another Onkyo component, refer to its instruction manual as well. Digital (Optical or Coaxial) Connection T-4030 Connect either of them. Amplifier Use the digital audio cable to connect the T-4030’s DIGITAL COAXIAL/OPTICAL jacks to the DIGITAL IN jacks on your amplifier, as shown. En-12 Connecting Your Components—Continued Connecting Onkyo R Components If you connect the T-4030 to another Onkyo R-capable component with the supplied R cable and audio cable, you can use the following system functions. R cables are special cables solely for use with Onkyo products. Auto Power On When you turn on the T-4030, your Onkyo amplifier will turn on automatically. (The amplifier’s POWER switch must be set to ON for this to work. ) Direct Change When you select a radio preset or change the band (FM, DAB), your Onkyo amplifier will automatically select the T-4030 as the input source. Remote Control Operation You can control the T-4030 by using your Onkyo amplifier’s remote controller. See the amplifier’s instruction manual for details. With R (Remote Interactive), you can control your R-capable Onkyo CD player, T-4030, and so on with your amp’s remote controller. Onkyo amplifier Connecting the Power Cord Connect the power cord to a suitable wall outlet. Note: • Before connecting the power cord, connect all of other components. Turning On and Standby k ON/STANDBY 1 Press the [k ON/STANDBY] button. Alternatively, press the remote controller’s [k ] button. The tuner comes on, and the display lights up. To turn the tuner off, press the [k ON/STANDBY] button, or press the remote controller’s [k ] button. The tuner will enter Standby mode. R jack Onkyo CD player R jack T-4030 Notes: • Push each plug in all the way to make a good connection. • Use only dedicated R cables for R connections. R cables are supplied with Onkyo tuners and players (DVD, CD, etc. ). • Some components, including the T-4030, have two R jacks. They’re both the same, so use either one. • R jacks should be connected only to Onkyo components. • Connecting them to another manufacturer’s component may cause a malfunction. • Some components may not support all R functions. See the manuals supplied with your other Onkyo components for more information. En-13 Listening to the Radio Listening to FM Stations With the built-in tuner, you can enjoy FM radio stations. BAND Manual Tuning To activate this mode, press the [TUNING MODE] button to turn off the “AUTO” indicator. In this mode, you will receive the broadcast in monaural sound. 3 Press the TUNING [a] or [s] button. [. . . ] If you can’t resolve the issue yourself, try resetting the tuner before contacting your Onkyo dealer. To reset the tuner to its factory defaults, turn it on and, while holding down the [TUNING MODE] button, press the [k ON/STANDBY] button. Remote Controller The remote controller doesn’t work • Make sure that the batteries are installed with the correct polarity ( page 6). Don’t mix different types of batteries or old and new batteries ( page 6). • Make sure that the remote controller is not too far away from the receiver, and that there’s no obstruction between the remote controller and the receiver’s remote control sensor ( page 6). [. . . ]