User manual ONKYO T-4037 service manual

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safeguards 1. Read Instructions ­ All the safety and operating instructions should be read before the appliance is operated. Retain Instructions ­ The safety and operating instructions should be retained for future reference. [. . . ] · It is dangerous to put the antenna close to power lines. Keep it well away from power lines, etc. · To avoid the risk of lightning and electrical shock, grounding is necessary. Follow item 19 of the "Important Safeguards" on page 3 when you install the outdoor antenna. U. S. and Canadian models Other models 75 ohms coaxial cable 300 75 FM AM 10 ANTENNA ANTENNA FM 75 Connecting the AM antenna (U. S. and Canadian models only) · AM reception is available only on the U. S. Assembling the AM loop antenna Assemble the loop antenna as shown in the illustration. Before Using Insert into the hole. Connecting the antenna cable 1. Close the lever. Connections Connecting the AM loop antenna The AM loop antenna is for indoor use only. Set it in the direction and position where you receive the clearest sound. Put it as far as possible away from this unit, TV, speaker cables, and power cords. Operation 300 75 FM AM ANTENNA Connecting an AM outdoor antenna When reception is not satisfactory with the supplied AM loop antenna alone, connection of an outdoor antenna is recommended. The outdoor antenna will be more effective if it is stretched horizontally above a window or outside. If so, follow the manual clock adjustment procedure described on page 14. · There may be cases in which you can listen to r a d i o b ro a d c a s t s b u t c a n n o t u s e t h e ACCUCLOCK function. · Once activated, ACCUCLOCK will remember the RDS station it uses for several weeks even if the power cord of the tuner is unplugged. If you move outside the service area of the memorized RDS station and find out that ACCUCLOCK is not functioning, see "Confirming/changing the RDS Station used by ACCUCLOCK" on page 13 to change the memorized RDS station. POWER INPUT SELECTOR MEMORY TIMER PRESET® FM STEREO TUNER PRESET TIMER MEMORY CLEAR G. EQUALIZER ACOUSTIC MODE CLOCK CALL SLEEP PRESENCE EFFECT TUNER PRESET TAPE FM AM DVD PAUSE/STEP REPEAT SCROLL MD PLAY MODE CLEAR REC AUTO / MONO STANDBY/ ON REPEAT RANDOM CD TUNING MEMORY CLEAR DISC DISPLAY CHARACTER ACCUCLOCK T-4037 TIMER UP/DOWN ENTER TIMER 1 CD/MD 2 3 4 5 6 UP/DOWN 7 8 9 VOLUME ENTER --/--- 10/0 MUTING REMOTE CONTROLLER RC-398S The remote controller comes with the Onkyo A-905X amplifier. Before Using The following procedures are based on the front panel of the T-4037. However, you can also perform the procedure using the remote controller that comes with Onkyo A-905X amplifier. On the remote controller, press the "ENTER" button and "UP/DOWN" button instead of the "MEMORY" button and PRESET/® button respectively. 2 If "AUTO" appears on the display, press the MEMORY button. If "MANUAL" appears on the display, press the PRESET or ® button to select "AUTO, " then press the MEMORY button. MEMORY Connections Confirming/changing the RDS station used by ACCUCLOCK If you wish to know which RDS station has been used to set the clock by ACCUCLOCK, or to use a different RDS station signal to set the clock, follow the steps below: MHz 1 Press the TIMER button repeatedly until "ADJUST" is selected on the display, then press the MEMORY button. TIMER The example shown above indicates that the ACCUCLOCK function uses the RDS station whose information appears on the display (FM 88. 10 MHz). If RDS station signals cannot be received successfully, "- -. --" will appear instead of the radio frequency of the station. If you wish to change the selected RDS station or if no RDS station is selected, choose the desired RDS station by using the PRESET or ® button, then press the MEMORY button. Operation Other Information MEMORY "AUTO" or "MANUAL" appears on the display. 13 Setting the Clock POWER INPUT SELECTOR MEMORY TIMER PRESET® FM STEREO TUNER PRESET TIMER MEMORY CLEAR G. EQUALIZER ACOUSTIC MODE CLOCK CALL SLEEP PRESENCE EFFECT TUNER PRESET TAPE FM AM DVD PAUSE/STEP REPEAT SCROLL MD PLAY MODE CLEAR REC AUTO / MONO STANDBY/ ON REPEAT RANDOM CD TUNING MEMORY CLEAR DISC DISPLAY CHARACTER ACCUCLOCK T-4037 TIMER UP/DOWN ENTER TIMER 1 CD/MD 2 3 4 5 6 UP/DOWN 7 8 9 VOLUME ENTER --/--- 10/0 MUTING REMOTE CONTROLLER RC-398S The remote controller comes with the Onkyo A-905X amplifier. Setting the clock manually The following procedures are based on the front panel of the T-4037. However, you can also perform the procedure using the remote controller that comes with Onkyo A-905X amplifier. On the remote controller, press the "ENTER" button and "UP/DOWN" button instead of the "MEMORY" button and PRESET/® button respectively. 2 Press the PRESET or ® button until the desired day of the week is selected, then press the MEMORY button. PRESET MEMORY The time will flash on the display. 1 Press the TIMER button until "ADJUST" is selected on the display, then press the MEMORY button. TIMER 3 Use the PRESET or ® button to set the desired time. PRESET MEMORY The day of the week will flash on the display. [. . . ] · Noise from automobile ignition. · Multiple reflection of the radio waves because of tall buildings or mountains. · Move the antenna as far away as possible from the fluorescent lamp. · Install an outdoor FM antenna as far away as possible from the road. [. . . ]