User manual ONKYO T-4087 service manual

[. . . ] Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new Tuner. Please retain this manual for future reference. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · The remote controller may not work reliably if the A-9355/A-9155 is installed in a rack behind colored glass doors. · The remote controller will not work if there's an obstacle between it and the A-9355/A-9155's remote control sensor. 9 Connecting the T-4087 Before Making Any Connections · Refer to the instructions that came with the component you are connecting. · Do not plug in the power cord until all other connections are complete. · Do not bind audio cables with power cords and speaker cables. Doing so may adversely affect the sound quality. · To prevent interference, keep power cords and speaker cables as far away as possible from the tuner's antennas. RCA Audio Connection Color Coding · Red connectors are used for the right channel, and white connectors are used for the left channel. Left (white) L Right (red) R · Push each plug in all the way to make a good connection (loose connections can cause noise or malfunctions). Right! Wrong! Connecting an amplifier Use the supplied audio cable to connect the T-4087's ANALOG AUDIO OUTPUT L/R jacks to the analog input jacks on the amplifier, as shown. To use the system functions, use the supplied cable to make an connection. T-4087 Supplied audio cable L Supplied cable CD PHONO TUNER MD TAPE DOCK POWER BASS A SPEAKERS B PHONES PURE DIRECT OFF OFF TREBLE LOUDNESS R TUNER ON OFF MUTING ON ON STANDBY Amplifier Notes: · The T-4087 has two jacks. They're both the same, so you can use either one. · To use , you must make an audio connection between the T-4087 and the other component. · Use only dedicated cables for connections. · If the T-4087 is used with another Onkyo component, such as the A-9355/A-9155, refer to its instruction manual as well. 10 Connecting the T-4087--Continued About the System Functions If you connect the T-4087 to another Onkyo -capable component with the supplied cable and audio cable, you can use the following system functions. · Outdoor antenna should be located away from possible noise sources, such as neon signs, busy roads, etc. · For safety reasons, outdoor antenna should be situated well away from power lines and other high voltage equipment. · Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards. Black Outdoor AM antennas work best when installed outside horizontally, but good results can sometimes be obtained indoors by mounting horizontally above a window. Note that the AM loop antenna should be left connected. Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards. Using a TV/FM Antenna Splitter It's best not to use the same antenna for both FM and TV reception, as this can cause interference problems. If circumstances demand it, use a TV/FM antenna splitter, as shown. TV/FM antenna splitter To T-4087 To TV (or VCR) 13 Turning On the T-4087 POWER Listening to the Radio Tuning into Radio Stations Manually TUNING 1 Plug the power cord into a suitable wall outlet (or the AC OUTLET on the A-9355/A-9155's rear panel). To turn off the T-4087, press the [POWER] switch. BAND 2 1 Use the [BAND] button to select FM or AM. The band switches between FM and AM each time you press the button. 2 Using the A-9355/A-9155's Remote Controller ON Use the TUNING [ ]/[ ] buttons to tune into a station. The tuning frequency is shown on the display. For each button press, the frequency will change in 0. 05 MHz steps for FM, and 9 kHz steps for AM. If you hold down the button for more than 0. 5 second, the T-4087 will find the next station automatically. RC-627S (remote controller supplied with the A-9355/A-9155) If you're using the T-4087 together with the A-9355/A-9155 Onkyo amplifier, press the remote controller's [ON] button to turn on the T-4087 and A-9355/A-9155. [. . . ] · Make sure that the power cord is properly plugged into the wall outlet (page 14). · Unplug the power cord from the wall outlet, wait five seconds or more, then plug it in again. Audio There's no sound. · The T-4087 is not connected properly. Check all connections and correct as necessary. [. . . ]