User manual ONKYO T-433

[. . . ] *En_T433_01. fm Page 1 Tuesday, February 15, 2005 3:09 PM Contents FM/AM Tuner Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 T-433 Instruction Manual Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Enjoying Audio Sources. . . . . . . . . . . . . . 14 Thank you for purchasing an Onkyo FM/AM Tuner. [. . . ] You can save energy by leaving the clock display turned off while the T-433 is on Standby. 15 *En_T433_02. fm Page 16 Tuesday, February 15, 2005 3:09 PM Listening to the Radio You can store up to 30 of your favorite radio stations as presets for quick selection. Stations can be preset automatically using the Auto Preset function or manually. Notes: · You can preset up to 30 FM/AM stations. If you try to store more than this, the message "FULL" will appear on the display. · Using the remote controller while listening to an AM radio station may cause interference. · If the power cord is disconnected, or the power is off for more than 2 weeks, the preset settings may be lost, in which case, you'll need to store them again. Presetting Stations Manually Here you can tune into stations individually and store them as presets. This allows you to store stations in any order you like. Notes: · You can store up to 30 stations, and this can be any combination of FM and AM stations. For example, 17 FM stations and 13 AM stations, or 8 FM stations and 22 AM stations. · Although the numbering schemes for FM and AM presets both start at 1, it doesn't matter because FM and AM presets are selected independently. · Stations can be stored to presets in any order. For example, you could store some AM stations to presets 2, 1, 9, and so on. TUNING indicator KEY MODE MEMORY Presetting All Stations Automatically (Auto Preset) With the Auto Preset function, you can search and store all of the radio stations available in your area in one go. Notes: · All existing presets will be replaced when the Auto Preset function is used. · Be sure that your antennas are positioned so as to obtain the best possible reception (see page 12). MEMORY ACCUCLOCK TUNING PRESET STANDBY/ON KEY MODE TIMER CLEAR MEMORY FM MODE BAND DISPLAY STANDBY TUNING / PRESET BAND TUNING/PRESET ACCUCLOCK TUNING PRESET STANDBY/ON KEY MODE TIMER CLEAR MEMORY FM MODE BAND DISPLAY STANDBY TUNING / PRESET 1 BAND Use the [BAND] button to select FM or AM. MEMORY Press and hold the [MEMORY] button for about 5 seconds until auto tuning starts. When the [MEMORY] button is pressed, first, the MEM indicator lights up. Next, "AUTO PRESET" flashes on the display, followed by the tuning frequency, and then auto tuning starts. When a station is found, auto tuning stops and the indicator lights up. AUTO MEM The band switches between FM and AM each time you press the button. 2 KEY MODE TUNING PRESET Use the [KEY MODE] button to select Tuning mode (TUNING indicator on). The mode switches between Tuning and Preset each time you press the button. Press a TUNING/PRESET [ ]/[ ] button for 1 second until auto tuning starts. 3 Starting at the bottom of the frequency band, the T-433 automatically tunes and stores up to 20 FM stations, then up to 10 AM stations. Note: Depending on your location, a preset may be stored with no station and you'll hear only noise when you select it. In this case, delete the preset (see page 19). TUNING / PRESET The frequency display changes during auto tuning. Auto tuning stops when a station is found. 16 *En_T433_02. fm Page 17 Tuesday, February 15, 2005 3:09 PM Listening to the Radio--Continued 4 MEMORY Press the [MEMORY] button. MEM indicator Selecting Preset Stations You must store some presets before you can select them (see page 16). PRESET indicator KEY MODE The MEM indicator appears and the preset number flashes. [. . . ] Move power cords and speaker cables as far away as possible from the tuner's antenna. Cars or airplanes can cause noisy interference. The radio signal will be weakened if it has to pass through a concrete wall before reaching the antenna. When listening to an AM station, noise may be heard when you operate the remote controller. [. . . ]