User manual ONKYO T-4700

[. . . ] TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. q Declaration of Conformity We, ONKYO EUROPE ELECTRONICS GMBH INDUSTRIESTRASSE 18/20 82110 GERMERING, GERMANY declare in own responsibility, that the ONKYO product described in this instruction manual is in compliance with the corresponding technical standards such as EN55013, EN55020, EN60555-2, EN60065 GERMERING, GERMANY H. YAMAZOE ONKYO EUROPE ELECTRONICS GMBH a. e. b. f. CAUTION: q c. Sur les modèles dont la fiche est polarisée. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. Memory Preservation This unit does not require memory preservation batteries. A built-in memory power back-up system preserves the contents of the memory during power failures and even when the unit is unplugged. The unit must be plugged in order to charge the back-up system. [. . . ] Auto tuning setting ("AUTO" lights up. ): Turn the PRESET/ TUNING dial to begin auto-tuning. The frequency changes in steps of 50 kHz (or 200 kHz) when tuning an FM station or in steps of 9 kHz (or 10 kHz) when tuning an AM station. * The steps in which the frequency is changed differ according to the country of purchase. The frequency steps shown in ( ) are for the USA and Canadian model. Manual fine setting ("FINE" lights up. ): Turn the PRESET/ TUNING dial to manually tune in the station. The FM frequency changes in steps of 25 kHz. Manual fine monaural setting ("FINE" and "MONO" light up. ): This setting is like the previous one, except it plays the broadcast in MONO so that even a station with a weak signal can be received. s ANTENNA Button If antennas have been connected to both the A and B FM antenna connectors on the rear panel, select the one with better sensitivity using the ANTENNA button on the remote control. The antenna A/B selection status will be memorized at the Preset Station Buttons. s IF BAND button When FM stations are mixed or there is interference, this button corrects this as much as possible. Each press switches it as follows: NORMAL/NARROW. Normal mode (NORMAL) is selected for normal reception. Narrow mode (NARROW) is selected when other stations may be at frequencies that are close to the desired station. When a station is received with the desired PTY, the scanning stops for approximately 5 seconds, before the unit starts scanning again. When the desired station is reached, press SCAN again to stop scanning. RDS IF BAND HI-BLEND (For European models) PRESET / TUNING TUNED STEREO NARROW 3 DISPLAY GROUP SCAN 4 DISPLAY GROUP SCAN 13 Receiving RDS 1 Receiving RDS traffic information RDS (For models other than European models) STEREO NARROW AUTO RDS IF BAND HI-BLEND (For European model) 1. Press the RDS button until "TP Search" appears on the display. Press the SCAN button to start searching for a TP station. When the unit receives a TP station, it stops scanning. If the unit cannot receive any signal, "Not find" (cannot find the station) is shown on the display. NOTE: If the TP indicator in the top left of the display lights up, the current station is broadcasting traffic information. 2 DISPLAY GROUP SCAN 1 RDS (For models other than European models) STEREO NARROW AUTO Searching for the station which sends the clearest and strongest signal. (AF search) If the station you are listening to is not an RDS station, this search function cannot be used. Press the RDS button until "AF Search" appears on the display. Press the SCAN button to start searching for the strongest signal that this station can be received on. If an AF list cannot be received, "No AF List" is shown on the display. RDS IF BAND HI-BLEND (For European model) 2 DISPLAY GROUP SCAN Displaying Radio Text (RT) If the station you are listening to is not an RDS station, this function cannot be used. [. . . ] · AM stations cannot be received. (For models other than European models) Cause: AM loop antenna is not attached. Remedy: Connect the included AM loop antenna to the AM antenna terminals. · TUNED indicators and stereo indicator light but sound is distorted and separation is bad. [. . . ]