User manual ONKYO TA-6510

[. . . ] Please retain this manual for future reference. En Introduction WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Install in accordance with the manufacturer's instructions. [. . . ] · Speakers that you set to "No" or "None" in "Sp Config (Speaker Configuration)" ( page 41) cannot be selected. *1 For the center speaker and subwoofer, the level settings made by using Home menu are saved here as the default settings. Tip · If you're using a handheld sound level meter, adjust the level of each speaker so that it reads 75 dB SPL at the listening position, measured with C-weighting and slow reading. Wireless SW (Subwoofer) Yes: The audio is output from the subwoofer connected to the wireless unit. No: The audio is not output from the subwoofer connected to the wireless unit. When the wireless unit is connected to the UNIVERSAL PORT jack on the AV receiver, you can select if you wish to output the audio from the subwoofer connected to the wireless unit. Note · If the "Subwoofer" setting is set to "No" ( page 41), this setting cannot be selected. Sp Distance (Speaker Distance) Menu Sp Distance This setting is set automatically by Audyssey 2EQ® Room Correction and Speaker Setup ( page 28). Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arrives at the listener's ears as the sound designer intended. Unit feet: Distances can be set in feet. (The default setting varies from country to country. ) En 42 Audio Adjust Menu Audio Adjust With the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like. Multiplex/Mono Multiplex Input Ch (Mux) Main Sub Main/Sub This setting determines which channel of a stereo multiplex source is output. Use it to select audio channels or languages with multiplex sources, multilingual TV broadcasts, and so on. Mono Input Ch (Mono) Left+Right Left Right This setting specifies the channel to be used for playing any 2-channel digital source such as Dolby Digital, or 2channel analog/PCM source in the Mono listening mode. Center Width 0 to 3 to 7 With this setting, you can adjust the width of the sound from the center speaker when using the Dolby Pro Logic IIx Music listening mode. Normally, if you're using a center speaker, the center channel sound is output only from the center speaker. To enable the following settings, you must first perform the Room Correction and Speaker Setup ( page 28). Audyssey Off Movie: Select this setting for movie material. The Audyssey indicator will light ( page 8). Music: Select this setting for music material. The Audyssey indicator will light ( page 8). Note · When "Audyssey Quick Start" has been used for measurement, the "Audyssey" cannot be selected. · Audyssey equalizing does not work for DSD sources. · These technologies cannot be used when: ­ a pair of headphones is connected, or ­ either Pure Audio (European, Australian and Asian) or Direct listening mode is selected. Reference Level Audyssey Dynamic EQ Reference Level Offset 0 dB: It should be used when listening to movies. 5 dB: Select this setting for content that has a very wide dynamic range, such as classical music. 10 dB: Select this setting for jazz or other music that has a wider dynamic range. This setting should also be selected for TV content as that is usually mixed at 10 dB below film reference. 15 dB: Select this setting for pop/rock music or other program material that is mixed at very high listening levels and has a compressed dynamic range. [. . . ] · Do not connect the AV receiver to another AV receiver/AV amplifier via HDMI. · Proper linked operations are not guaranteed when more -compatible components than the above-mentioned quantities are connected. Not all functions may operate depending on the model. En 72 How to connect and setup 3 1 Confirm the connection and settings. Connect the HDMI OUT jack to the HDMI input jack of the TV. Blu-ray Disc/DVD player, etc. HDMI connection AV receiver DIGITAL AUDIO connection (OPTICAL) HDMI connection TV, projector, etc. 2. Connect the audio output from the TV to the OPTICAL IN 2 jack of the AV receiver using an optical digital cable. Note · When the audio return channel (ARC) function is used with an ARC capable TV, this connection is not necessary ( page 48). Confirm the settings. [. . . ]